background image

Cautions and Warnings

Environmental Specifications

Cautions and Warnings

Environmental Specifications

Equipment must be used only with UL Listed ITE or Equivalent.

L'équipement doit être utilisé uniquement avec UL ITE ou équivalent.

Serveur-blades, cartes et modems doivent être des accessoires listés ou commutateurs, processeurs, serveurs et
similaire blades ou cartes doivent être listé UL ou équivalent.

Refer to specific Product Model Data Sheet for Environmental Specifications (Operating Temperature, Storage
Temperature, Humidity, and Altitude)

Référez à la Fiche Technique de ce produit pour les caractéristiques environnementales (Température de
fonctionnement, température de stockage, humidité et l'altitude).

Safety

Battery

– Risk of explosion if the battery is replaced by an incorrect type. Do not dispose of batteries in a fire.

They may explode. Dispose of used batteries according to your local regulations. IMPORTANT: Switzerland:
Annex 4.10 of SR814.013 applies to batteries.

Batterie

– Risque d'explosion si la batterie est remplacée par un type incorrect. Ne jetez pas les batteries au feu.

Ils peuvent exploser. Jetez les piles usagées conformément aux réglementations locales. IMPORTANT: Suisse:
l'annexe 4.10 de SR814.013 s’appliquent aux batteries.

警 告

本 電 池 如 果 更 換 不 正 確 會 有 爆 炸 的 危 險

請 依 製 造 商 說 明 書 處 理 用 過 之 電 池

Fiber optic transceiver must be rated 3.3V, 22mA max, Laser Class 1, UL certified component.

Le transceiver optique doit avoir les valeurs nominales de 3.3 V, maximum 22 mA, Laser Class 1, homologué UL

FIM-7920E Interface Module Guide
Fortinet Technologies Inc.

24

Summary of Contents for FIM-7920E




























Reviews: