background image

FortiGate-3600A FortiOS 3.0 MR6 Install Guide

32

01-30006-0457-20080318

Restoring a configuration

Configuring

Restoring a configuration

Should you need to restore the configuration file, use the following steps.

To restore the FortiGate configuration

1

Go to 

System > Maintenance > Backup & Restore

.

2

Select to upload the restore file from your PC or a USB key.

The USB Disk option will be grayed out if the FortiGate unit supports USB disks 
but none are connected.

3

Enter the path and file name of the configuration file, or select Browse to locate 
the file.

4

Enter a password if required.

5

Select Restore.

The FortiGate unit will load the configuration file and restart. Once the restart has 
completed, verify that the configuration has been restored.

Additional configuration

With the FortiGate connected and allowing traffic to pass-through, there are a few 
other configuration. While not mandatory, they will help in ensuring better control 
with the firewall.

Set the time and date

For effective scheduling and logging, the FortiGate system date and time must be 
accurate. You can either manually set the system date and time or configure the 
FortiGate unit to automatically keep its time correct by synchronizing with a 
Network Time Protocol (NTP) server.

To set the date and time

1

Go to 

System > Status

.

2

Under 

System Information > System Time

, select Change.

3

Select your Time Zone.

4

Optionally, select Automatically adjust clock for daylight saving changes.

5

Select Set Time and set the FortiGate system date and time.

6

If you want to synchronize the time with an NTP server, enable the option.

7

Select OK.

Set the Administrator password

The default administrator password is no password. You will want to apply a 
password to prevent anybody logging into the FortiGate and changing 
configuration options.

Note: 

If you choose the option Automatically adjust clock for daylight saving changes, the 

system time must be manually adjusted after daylight savings time ends. 

Summary of Contents for FortiGate 3600A

































































Reviews: