Fortinet FortiGate 5001FA2-LENC Manual Download | Manualshive

Page: 5 / 34

background image

FortiGate-5001FA2-LENC security system

FortiGate-5001FA2-LENC Security System Guide
01-30000-76602-20080606

5

FortiGate-5001FA2-LENC security
system

The FortiGate-5001FA2-LENC security system is a high-performance FortiGate
security system with a total of 8 front panel gigabit ethernet interfaces and two
base backplane interfaces. Use the front panel interfaces for connections to your
networks and the backplane interfaces for communication between
FortiGate-5000 series boards over the FortiGate-5000 chassis backplane.

You can also configure two or more FortiGate-5001FA2-LENC boards to create a
high availability (HA) cluster using the base backplane interfaces for HA heartbeat
communication through chassis backplane, leaving all eight front panel gigabit
interfaces available for network connections.

FortiGate-5001FA2-LENC front panel interfaces 1 and 2 also include accelerated
packet forwarding and policy enforcement for faster small packet performance.

The FortiGate-5001FA2-LENC board also supports high-end FortiGate features
including 802.1Q VLANs, multiple virtual domains, 802.3ad aggregate interfaces,
and FortiGate-5000 chassis monitoring.

Figure 1: FortiGate-5001FA2-LENC front panel

The FortiGate-5001FA2-LENC board includes the following features:

• A total of eight front panel gigabit interfaces

• Two accelerated packet forwarding and policy enforcement gigabit

interfaces that can accept optical Small Formfactor Pluggable (SFP) or
copper SFP gigabit transceivers (interfaces 1 and 2)

• Two gigabit interfaces that can accept optical or copper SFP gigabit

transceivers (interfaces 3 and 4)

• Four 10/100/1000Base-T gigabit copper network interfaces (interfaces 5, 6,

7, 8)

• Two base backplane gigabit interfaces (port9 and port10) for HA heartbeat and

data communications across the FortiGate-5000 chassis backplane.

• DB-9 RS-232 serial console connection
• One USB connector

3 4 Optical or Copper

SFP Gigabit

1 2 Optical or Copper

SFP Gigabit

Accelerated

5 6 7 8

Gigabit Copper

Handle

Status

Module

Position

Power

USB

Flash Disk

Access

RS-232

Serial

Handle

Retention

Screw

Retention

Screw

Link/Traffic

«
...
3
4
5
6
7
...
»

Summary of Contents for FortiGate 5001FA2-LENC



































Reviews:

No comments

Related manuals for FortiGate 5001FA2-LENC

Brand: Tandberg Data Pages: 67

Brand: Fortinet Pages: 2

FWG114P - ProSafe 802.11g Wireless Firewall

Brand: NETGEAR Pages: 70

Brand: ZyXEL Communications Pages: 668

Brand: Cisco Pages: 42

Brand: Cisco Pages: 20

Brand: Huawei Pages: 6

Brand: AirTies Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands