background image

  
 
 
 

 
 
 

 

 

Test the bike regularly and check that the unit is operating normally and safely.  

 

Always keep your bike clean.  

 

Keep the battery poles clean to prevent reduced efficiency or burnt poles. 

 

Your electric bike should undergo a professional annual check-up. If you are not 
confident carrying out any step, contact your local bicycle shop. 

 

Adjusting Chain Tension 

The chain may eventually loosen after extended use. To adjust, contact your local bicycle 

shop. 

 

Adjusting Brakes 

 

Correct brake adjustment will help the bike control better and improve user safety.  

 

The brakes are adjusted in a similar fashion to any standard bicycle. It is important 
for the brakes to work correctly and that the electric cut-off devices to be in working 
order (Electric cable to the brake levers). 

 

Once the brakes have been adjusted, turn the wheels and ensure that there is no 
binding.  

 

Confirm that the motor cuts out when either brake lever is pulled. 

 

Lubrication 

For a long service life, the following parts should be lubricated every 6 months: 

 

Front axle 

 

Chain 

 

Rear axle 

 

Freewheel 

 

Front fork and other parts which rotate 

Electrical parts are factory lubricated and do not require re-lubrication by the user. If you find 
anything wrong, contact Kogan.com or your local bicycle shop. 

 

Cleaning 

 

Clean with a damp sponge, taking care not to get electrical parts wet (battery 
connection, motor in the rear axle, electric cables, handlebar controls, etc.).  

 

Do not use a steady stream of water as this may result in damage to electrical 
components. 

 

The bicycle’s finish is durable and does not need to be waxed. Clean with a mild 
detergent and buff to restore its original shine if needed. Dry with a cloth.

 

 

                                      CLEANING & CARE 

WARNING: 

Before performing any maintenance, turn off the power and 

remove the ignition key. 

 

Summary of Contents for FS20FATEBKB




















Reviews: