background image

Before operation

Usage

Cleaning and maintenance

Operating Temperature

4

1. Contact an installation specialist for installation.
2. Do not use a damaged or non-standard power cord.
3. Do not share the same outlet with other appliances.

1. Exposure to direct airflow for a long period of time could be hazardous to the

health. Do not expose occupants, pets, or plants to direct airflow for a long
period of time.

2. Due to the possibility of oxygen deficiency, ventilate the room when use together

with stoves or other heating devices.

3. Do not use the air conditioner for non-specified purposes (e.g. preserving precision

devices, food, pets, plants, and art objects), otherwise it could harm the property.

1. Do not touch the metal parts of the unit when removing the filter. Injuries may occur

when handling sharp metal edges.

2. Do not use water to clean  the air conditioner inner. Water enter the unit can degrade

the insulation and may lead to electric shock.

3. Make sure the unit power and the circuit breaker are turned off before cleaning and

maintenance.

SAFETY INSTRUCTION 

If the unit is operated beyond the conditions specified above ,it may cause a failure of the unit.

Cooling operation

Outdoor temp:

O

18-43 C

Indoor temp:

O

17-32 C

Notes:

 The indoor relative humidity should be less than 80%. If the unit is used in a condition with a 

relative humidity over 80%, there will be condensed water on the appearance of the unit.

Summary of Contents for FWAC08M16

















Reviews: