USB port
RS-232 port
Intelligent slot
To allow for unattended UPS shutdown/start-up and status monitoring, connect one end of the communication cable to
the USB/RS-232 port, and the other end to the communication port of your PC. With the monitoring software installed, you
can schedule UPS shutdown/start-up and monitor its status through a PC.
The UPS is equipped with intelligent slot perfect for either SNMP card. When installing a SNMP card in the UPS, it will
provide advanced communication and monitoring options.
Note
: The USB and RS-232 ports cannot be used at the same time.
Network/Fax/Phone port
Connect the network surge protection
The UPS has two network cable RJ45 connectors for network lines
• Connect a single line modem/phone/fax cable into the network surge-protection “IN” jack on the rear panel of the UPS.
• Connect a network cable from the OUT jack on the rear of the UPS to a port on a PC or network device such as a router.
Turning on the UPS
Press the
ON/Mute
button on the front panel for two seconds to power on the UPS.
Note:
The battery charges fully during the first five hours of normal operation. Do not expect full battery run capability
during this initial charge period.
Communication port:
ForzaTracker
is a new generation of UPS monitoring software, which provides user-friendly interface to monitor and control
your UPS system. This unique software provides safe auto-shutdown for multi-computer systems during power failures. With
this software, users can monitor and control any UPS on the same LAN no matter how far they might be from the UPS.
2-5. ForzaTracker monitoring software
Installation procedure for Windows users:
Use the supplied CD or go to the website: http://www.forzaups.com.
After clicking the software icon, choose the required operation system.
Follow the on-screen instructions to install the software.
When you finished downloading all required files, enter the serial No (installation password):
5242-87f6-64re-di8d-986u
to install the software (include the hyphens).
In order to access as Administrator, input the password:
111296
.
When your computer restarts, the management software will appear as a light blue round icon located in the system tray,
near the clock.
For Mac users, please refer to the ForzaTracker QIG inside the Mac folder.
1.
2.
3.
4.
5.
6.
ON/Mute button
OFF/Enter button
Select button
ON/Mute +
Select button
Turn on the UPS: Press and hold the
ON/Mute
button for at least 2 seconds
to turn on the UPS.
Mute the alarm: When the UPS is on battery mode, press and hold this
button for at least 5 seconds to disable or enable the alarm system.
This command would not apply when warnings or errors occur.
Up key: Press this button to display previous selection in the UPS
configuration menu.
Switch to UPS self-test mode: Press and hold
ON/Mute
button for 5 seconds
to perform the self-test in AC mode, ECO mode, or converter mode.
Turn off the UPS: Press and hold this button for at least 2 seconds to turn
off the UPS in battery mode. The UPS will remain in standby mode under
normal power conditions or transfer to Bypass mode provided it has been
enabled previously by pressing this button.
Confirm selection key: Press this button to confirm the selection in the
UPS configuration menu.
Switch LCD message: Press this button to change the LCD message for
input voltage, input frequency, battery voltage, output voltage and output
frequency.
Setting mode: Press and hold this button for 5 seconds to enter the UPS
configuration menu while UPS is in standby or bypass mode.
Down key: Press this button to display the next selection in the UPS
configuration menu.
Switch to bypass mode: When the utility power is normal, press
ON/Mute
and
Select
buttons simultaneously for 5 seconds to transfer the UPS to
bypass mode. This action will be ineffective if the input voltage is not within
an acceptable range.
Button
Function
3. Advanced operation
3-1. Description of buttons and functions
Summary of Contents for FDC-1000T
Page 1: ...2 Y e a r W a r r a n t y...
