110
Model D2424LV Reference Manual (Changing the Initial Settings <SETUP mode>)
Flashing
Modifying (or deleting) stored time signatures
1.Repeat steps 1-3 described in the “Storing a time
signature” section.
2.Turn the Shuttle dial so that the flashing cursor is
on the time signature value.
3.Use the Jog dial to enter a new value.
Entering “
-/-
” deletes the existing data. Note that you
cannot enter “
-/-
” for measure 001.
4.Press the [EXECUTE/YES] key.
5.Press the [EXIT/NO] key (or [STOP] button).
<Caution>
If modifying or deleting the stored time signature
causes the bar/beat setting for the tempo specified in
the “
Setting a tempo
” menu to disappear, the tempo
setting will also be automatically erased.
To cancel the setting operation, or to exit SETUP mode
after storing data, press the
[STOP]
button or the
[EXIT/
NO]
key. Each time you press one of these keys, the
recorder returns to the previous hierarchy level of
the menu, and finally exits SETUP mode.
Clearing all time signature and tempo settings
<Caution>
Using this function will erase not only the time signature
setting but also the tempo data specified in the “
Setting
a tempo
” menu described in the next section.
1.Repeat steps 1-3 described in the “Storing a time
signature” section.
2. While the measure number is flashing, turn the Jog
dial counter-clockwise to select “All Clear?.”
When “
All Clear ?
” appears, “
SURE ?
” flashes, and you
can clear the time signature and tempo data in the next
step.
3.Press the [EXECUTE/YES] key.
The stored time signature and tempo data in its entirety
are cleared, and the initial settings are restored.
4.Press the [EXIT/NO] key (or [STOP] button).
To cancel the All Clear operation, press the
[STOP]
button or the
[EXIT/NO]
key now. Each time you press
one of these keys, the recorder returns to the previous
hierarchy level of the menu, and finally exits SETUP
mode.
Changing the bar at ABS “0” of the time base
Bar in -002bar/1beat/00clk, which indicates the head figure of the disk in the time base BAR/BEAT/CLK, can be changed.
Although the initial figure is -002bar, this can be set within the range of -009bar ~ -002bar.
Flashing
1.Repeat steps 1-2 described in the “Storing a time
signature” section.
2.Turn the Jog dial counter-clockwise to select
“-002 bar Offset.”
3.Press the [EXECUTE/YES] key.
“
2
” in “
-002bar
” will flash and the bar figure can be
changed with the
Jog
dial (Numbers that can be input
are 2~9.)
4. Use the Jog dial to enter a new value.
5. Press the [EXECUTE/YES] key.
6. Press the [EXIT/NO] key (or [STOP] button).
To cancel the setting operation, or to exit SETUP mode
after storing data, press the
[STOP]
button or the
[EXIT/
NO]
key. Each time you press one of these keys, the
recorder returns to the previous hierarchy level of
the menu, and finally exits SETUP mode.
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
SURE?
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
