29
Model VM88 Owner’s Manual
Doubling effect parameters (parameter type: DOUBLING)
For effect type
34
of the preceding "Effect type" table, the following three parameters can be adjusted.
1.
Lch DELAY TIME
Adjust the delay time of the L channel. Range:
0.1--9.9 ms
(99 steps in 0.1 ms units),
10-
-99 ms
(90 steps in 1 ms units),
100--200 ms
(51 steps in 2 ms units)
* The ENTER key / foot switch cannot be used for tap input.
2.
Rch DELAY TIME
Adjust the delay time of the R channel. Range:
0.1--9.9 ms
(99 steps in 0.1 ms units),
10-
-99ms
(90 steps in 1 ms units),
100--200 ms
(51 steps in 2 ms units)
* The ENTER key / foot switch cannot be used for tap input.
3.
FILTER
Adjust the tone of the delay sound. Range:
L9~L1, -, H1~H9
*
[-]
is Filter Off
*
L1~L9
= LPF (larger numbers will lower the cutoff frequency)
*
H1~H9
= HPF (larger numbers will raise the cutoff frequency)
Chorus effect parameters (parameter type: CHORUS)
For effect type
35
of the preceding "Effect type" table, the following four parameters can be adjusted.
1.
DEPTH
Adjust the chorus depth. Range:
0--99
(100 steps in increments of 1)
2.
DOUBLING TIME
Adjust the time difference of the doubling effect. Range:
0--99
(100 steps in increments
of 1)
3.
DOUBLING BALANCE
Adjust the volume of the doubling effect. Range:
0--99
(100 steps in increments of 1)
4.
FILTER
Adjust the tone of the delay sound. Range:
L9~L1, -, H1~H9
*
[-]
is Filter Off
*
L1~L9
= LPF (larger numbers will lower the cutoff frequency)
*
H1~H9
= HPF (larger numbers will raise the cutoff frequency)
Flanger effect parameters (parameter type: FLANGE)
For effect type
36
of the preceding "Effect type" table, the following four parameters can be adjusted.
1.
RATE
Adjust the speed of modulation. Range:
0.1--2.0 Hz
(200 steps in 0.01 Hz units)
2.
DEPTH
Adjust the depth of modulation. Range:
0--99
(100 steps in increments of 1)
3.
MOD DELAY
Adjust the modulation delay. Range:
0--200
(201 steps in increments of 1)
4.
FEEDBACK
Adjust the number of modulation repeats. Range:
0--99
(100 steps in increments of 1)
Delay pitch effect parameters (parameter type: DELAY PITCH)
For effect type
38
of the preceding "Effect type" table, the following four parameters can be adjusted.
1.
PITCH
Adjust the amount of pitch shift. Range:
-24--0--+24
(49 steps in semitone units)
*
+/-12
is one octave.
+/-24
is two octaves.
2.
ADJUST
Make fine adjustments to the amount of pitch shift. Range:
-50--0--+50
(101 steps in
increments of 1)
*
+50
is a semitone sharp.
-50
is a semitone flat.
3.
DLY TIME
Adjust the delay time until the pitch-shifted sound is heard. Range:
0--500 ms
(251 steps
in increments of 2)
* The ENTER key / foot switch can be used for tap input (refer to page 27).
4.
FEEDBACK
Adjust the number of delay repeats. Range:
0--99
(100 steps in increments of 1)
Mono pitch effect parameters (parameter type: MONO PITCH)
For effect type
37
of the preceding "Effect type" table, the following three parameters can be adjusted.
1.
PITCH
Adjust the amount of pitch shift. Range:
-24--0--+24
(49 steps in semitone units)
*
+/-12
is one octave.
+/-24
is two octaves.
2.
ADJUST
Make fine adjustments to the amount of pitch shift. Range:
-50--0--+50
(101 steps in
increments of 1)
*
+50
is a semitone sharp.
-50
is a semitone flat.
3.
MODE
Select the processing method. Range:
1--3
(3 steps)
