background image

Care and Maintenance

To enjoy years of outstanding performance from your heater, make sure you perform the following 

maintenance activities on a regular basis:
Keep exterior surface clean.
Use  warm  soapy  water  for  cleaning.  Never  use  flammable  or  corrosive  cleaning  agents.                  

While cleaning your unit, be sure to keep the area around the burner and pilot assembly dry at all 

times. Do not submerge the control valve assembly. If the gas control is submerged in water, DO 

NOT use it. It must be replaceed.
Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean. Signs 

of possible blockage include:

• 

Gas odor with extreme yellow tipping of flame.

• 

Heater does NOT reach the desired temperature.

• 

Heater glow is excessively uneven.

• 

Heater makes popping noise.

• 

Spider and insects can nest in the burners of this or any other heater and cause the gas to   

flow from the front of the burner. This is a very dangerous condition which can cause a fire to 

occur behind the valve panel, thereby damaging the heater and making it unsafe to operate. We 

recommend you check the heater and remove any spiders, insects and webs at least once a year to 

reduce this risk.
• Carbon deposits may create a fire hazard. Clean dome and burner screen with warm soapy water 

if any carbon deposits develop.
Note: In a salt-air environment (such as near an ocean) corrosion occurs more quickly than normal. 

Frequently check for corroded areas and repair them promptly.

13

!

 

 WARNING

FOR YOUR SAFETY

DO NOT touch or move heater for at 

least 45 minutes after use. 

Reflector is hot to the touch. 

Allow reflector to cool before touching.

Location:

1. This portable heater is intended for outdoor       

use only. Always ensure that adequate fresh air 

ventilation is provided.
2. Always  maintain  proper  clearance  to 

combustible materials, 18 inches above and a 

minimum of 24 inches from the sides.
3. The heater must be fixed on a strong and 

stable table.
4. Never operate the heater in an explosive 

atmosphere like in areas where gasoline or other 

flammable liquids or vapors are stored.

Summary of Contents for FM35PHLP
















Reviews: