background image

USER MANUAL 

TVNext

TM

 (NN01-054) 

 

Last updated on June 2020

 

© 2020 FRACTUS ANTENNAS, S.L.   -  

 

11

 

5.

 

ASSEMBLY PROCESS

 

 

 
Figure 

5

  shows  the  back  and  front  view  of  the  TVNext

TM

  VHF  antenna,  and  indicates  the 

location of the feeding point and the mounting pads:

  

 

 

 

Figure 5 

– 

Pads of the TVNext

TM

 VHF chip antenna.

 

 
As a surface mount device (SMD), this antenna is compatible with industry standard soldering 
processes. The basic assembly procedure for this antenna is as follows: 
 
1.

 

Apply a solder paste to the pads of the PCB. Place the antenna on the board.  

2.

 

Perform a reflow process according to the temperature profile detailed in Table 3, Figure 7 
on page 12. 

3.

 

After soldering the antenna to the circuit board, perform a cleaning process to remove any 
residual  flux.  Fractus  Antennas  recommends  conducting  a  visual  inspection  after  the 
cleaning process to verify that all reflux has been removed. 

 
The drawing below shows the soldering details obtained after a correct assembly process: 
 

 

Figure 6 

– 

Soldering Details. 

 

NOTE(*):

 Solder paste thickness after the assembly process will depend on the thickness of the 

soldering  stencil  mask.  A  stencil  thickness  equal  to  or  larger  than 

127  microns  (5  mils)

  is 

required.

 

Summary of Contents for TVNext NN01-054















Reviews: