– 10 –
CE-50 / CE-75 / TE-50 / TE-75 / TE-75S / TE-125 / TE-125BF
EN
PLUG SOCKET
13 AMP FUSED
DOUBLE POLE
SWITCHED SPUR
WALL MOUNTED
ELECTRICAL CONNECTION
FOR DISPOSER PROVIDED
WITH PREWIRED MOLDED
PLUG AND LEAD.
For continuous feed only
- not batch feed
3A
13 AMP FUSED
DOUBLE POLE
SWITCHED SPUR
WALL MOUNTED
FIXED WIRE ELECTRICAL
CONNECTION
13 AMP FUSED
SPUR MOUNTED
UNDER SINK
3B
Replacing the fuse in moulded plugs
9
The correct fuse cover must be refitted when
changing the fuse.
9
Remove the fuse cover and slide the fuse out.
9
Replace it with a 13 Amp ASTA fuse (approved
to BS 1363). Should the fuse cover be lost or
damaged, an exact replacement should be used.
These are available from an approved service
agent, listed below. Never use the plug without
the fuse cover fitted.
Attaching discharge elbow
MODELS CE-50, CE-75, TE-75S
X
X
Connect the waste elbow to the disposer by
sliding the flange against the rubber gasket on the
elbow and tightening the screws into the disposer
(fig.
4A
). Then connect bottom of the elbow by
tightening the slip nut (fig.
4B
). If using a straight
pipe, it must have a lip similar to the one on the
elbow. Remove the gasket from the elbow and
install it on the straight pipe with the flat end of
the gasket facing toward the disposer discharge
opening.
4A
4B
P-TRAP
RUBBER
GASKET
If you are connecting to a dishwasher, return to
PLUMBING CONNECTION section (
2A
-
B
). If not,
make sure all plumbing connections are tight and in
accordance with all plumbing codes and ordinances.
Run water and check for leaks.
MODELS TE-50, TE-75, TE-125, TE-125BF
X
X
Depress the wings on the spring clamp to remove
it from the rubber sleeve. Slip the spring clamp
over the smooth side of the elbow and slide it
towards the lipped side of the elbow (fig.
4C
).
X
X
Insert the waste elbow into the rubber sleeve so
the elbow lip fits into the groove located inside
the rubber sleeve. Position the spring clamp over
the rubber sleeve and secure (fig.
4D
). If using a
straight pipe, use one with a lip matching the lip
on the elbow supplied with the disposer.
4C
SPRING
CLAMP
RING
4D
X
X
If you are connecting to a dishwasher, return to
PLUMBING CONNECTION section (
2A
-
B
). If not,
make sure all plumbing connections are tight
and in accordance with all plumbing codes and
ordinances. Run water and check for leaks.
Summary of Contents for CE-50
