– 8 –
CE-50 / CE-75 / TE-50 / TE-75 / TE-75S / TE-125 / TE-125BF
EN
X
X
Be sure the sink is clean. Install a bead of
plumbers putty to the sink flange (
1
). From top
of the sink, push the sink flange down against
the sink opening to make a good seal (
2
).
Do not
move or rotate
the sink flange once it has been
seated or the seal may be broken.
1
2
X
X
Place a heavy object, such as the disposer (use
a towel to prevent sink scratching) on top of the
sink flange to hold it down.
X
X
Take the remaining portion of the mounting
assembly, that was put aside. From under the sink
insert the fibre gasket (
3
), then the support
flange (
4
), and then the upper mounting ring (
5
).
X
X
Hold the three parts in place while attaching the
retainer ring (
6
) by pulling it apart and sliding it
onto the sink flange (
7
) until it snaps into the
groove of the sink flange (
7
).
3
4
5
6
7
8
X
X
Tighten the three mounting screws evenly and
firmly against the supporting flange (
8
). Do not
over tighten.
X
X
Trim off any excess plumber’s putty.
X
X
Attach disposer onto the upper mounting ring
by aligning the three mounting tabs on the
lower mounting ring with the slide-up ramps on
the upper mounting ring and rotating counter
clockwise.
A
C
B
X
X
The lower mounting ring (which is part of the
disposer) has 3 tabs that grab the mounting ring
ramp.
(
A
) points to the upper mounting ring.
(
B
) is the tab that slides up onto the “Ramp”.
(
C
) is the „Ear“ that is used to help rotate the lower
mounting ring.
X
X
Use a screwdriver for leverage if needed.
D
X
X
Lift and turn the lower mounting ring counter
clockwise until all three mounting tabs lock over
the ridges (
F
) on the slide-up ramps (
D
) of the
upper mounting ring.
F
E
X
X
As the lower mounting ring is turned counter
clockwise each tab slides up onto the upper
mounting ring ramp (
E
) and locks in position over
the ridges (
F
).
X
X
Use a screwdriver or hammer for leverage if
needed.
X
X
If a disposer needs to be removed, tapping on the
Ear clockwise with a hammer will easily loosen
the lower mounting ring.
3
Summary of Contents for CE-50
