background image

Replacement Parts

2

4

5

6

MAINTENANCE

8

9

10

7

6

1 - F2401CH      Lever Handle - chrome

1 - F2401OWB   Lever Handle - old world bronze

1 - F2401SN      Lever Handle - satin nickel

2 - F2402           Cartridge

3 - F2403CH      Valve Kit - chrome

3 - F2403OWB   Valve Kit - old world bronze

3 - F2403SN      Valve Kit - satin nickel

4 - F2404           Fastening set

7 - 2407CH        Hand shower - chrome (kitchen)

7 - 2407OWB     Hand shower - old world bronze (kitchen)

7 - 2407SN        Hand shower - satin nickel (kitchen)

7 - 2411CH       Hand shower - chrome (bar/prep)

7 - 2411OWB    Hand shower - old world bronze (bar/prep)

7 - 2411SN       Hand shower - satin nickel (bar/prep)

8 - 2408            Pull-out hose

9 - 2409            Counterweight

10 - 2410          Check Valve Assembly

11 - 2412          Hose Riser

5 - F2405           Supply Hose

6 - F2406           Aerator & Wrench

12 - 2413         1.75GPM Flow Restrictor

Before carrying out this operation make sure that water supply is turned off.

If the supply is off unscrew the aerator using the wrench supplied and remove it from its seat. If the aerator 

is clogged rinse it with running water without using detergents. If aerator is damaged replace it and 

assemble everything in the opposite sequence.

Aerator Cleaning / Replacement

1

2

11

12

Brand and 

Certification 

marks

Marks on 

backside when 

lever is installed 

right side

3

1

backside

Summary of Contents for FF2460









Reviews: