Franke FGAS/3 E FX 1000 CE XS WM, Instructions For Use And Installation

9

GB

e-  Check the connectors of the motor (

Fig 9)

.

f-   Test the lights and the fan motor.

g-  Fit the metal grease filters and close the deflector.

IN THE RECIRCULATION MODE:

a-  To carry out an inlet  for recycling air in the kitchen (

Fig.11

).

b-  Connect the ducting 150mm (6 INS) not provided between motors 

item 6

 and the recirculation spigot 

and secure the connections with appropriate clamping rings or adhesive tape (

Fig. 12

).

c-  Make the electrical connection of the motor as described in the section titled ELECTRICAL.

d-  Place the canopy under the motor housing and fix it with the crews provided as illustrated in 

Fig. 10

.  

Attention:  2 persons are necessary to secure this operation.

e-  Connect the electrical plug of the motor cord on the body hood (

Fig.7

).

f-  Check the connectors of the motor (

Fig 9)

.

g-

Test the lights and the fan motor.

h- Fit the charcoal filter onto the inlets of the motor (

Fig. 13

).

i-  Fit the metal grease filters and close the deflector.

• CLIPPAGE ON THE FALSE CEILING

2) Mark the centre of the cooking appliance onto the ceiling with a plumb line. Draw the horizontal axes 

running parallel to the stove top onto the ceiling as illustrated 

Fig. 1

.

3) To carry out the cutting of embedding in the suspended ceiling (

Fig 2a

).

4) To remove the lighting front panel (

Fig. 15

).

5) To unscrew the screws of the clips according to the thickness of the false ceiling (

Fig. 16

). When fixing 

the cooker hood to a plasterboard ceiling ensure it is reinforced as illustrated in 

Fig. 17. 

For the false 

ceiling in MDF of 18 mm, 4 holds of compensation (2 

m

m thickness) are provided with the hood.

6) Open the deflector ( 

Fig. 6 Rep. 12) 

by pushing / unlocking (

Fig. 14

).

7) To remove the metal filters.

IN THE EXTRACTION MODE:

a-  Fit the non-return backflow flaps 

C 

over the round outlet 

item 6

 on top of the canopy while pressing 

down until they snap into position, and then connect the ducting 150mm (6 INS) and secure the connec-

tions with appropriate clamping rings or adhesive tape (

Fig. 8

).

b-  Make the electrical connection of the motor as described in the section titled ELECTRICAL.

c-  Place the canopy under the motor housing and fix it with the screws provided as illustrated in 

Fig. 10

or clip the hood on the false ceiling (

Fig. 15

), to tighten the screws (

Fig. 16

) and to fit back the lighing 

front panel.  

Attention:  2 persons are necessary to secure this operation.

.

d-  Connect the electrical plug of the motor cord on the body hood (

Fig.7

).

e-  Check the connectors of the motor (

Fig 9)

.

f-   Test the lights and the fan motor.

g-  Fit the metal grease filters and close the deflector.

IN THE RECIRCULATION MODE:

a-  To carry out an inlet  for recycling air in the kitchen (

Fig.11

).

b-  Connect the ducting 150mm (6 INS) not provided between motors 

item 6

 and the recirculation spigot 

and secure the connections with appropriate clamping rings or adhesive tape (

Fig. 12

).

c-  Make the electrical connection of the motor as described in the section titled ELECTRICAL.

d-  Place the canopy under the motor housing and fix it with the screws provided as illustrated in 

Fig. 10

or clip the hood on the false ceiling (

Fig. 15

), to tighten the screws (

Fig. 16

) and to fit back the lighing 

front panel.   

Attention:  2 persons are necessary to secure this operation.

e-  Connect the electrical plug of the motor cord on the body hood (

Fig.7

).

f-  Check the connectors of the motor (

Fig 9)

.

g-

Test the lights and the fan motor.

h- Fit the charcoal filter onto the inlets of the motor (

Fig. 13

).

i-  Fit the metal grease filters and close the deflector.