background image

The E -scooter is guaranteed according to the current legal deadlines.
The warranty excludes wear parts such as batteries, tires, hoses, rims, brake parts, wheel bearings, 
steering head bearings.
Also excluded are damages due to improper use, in particular jumping, descending steps, sidewalks, 
stairs and the like, running on muddy ground, sand or gravel, and overloading due to excessive weight. 
Gross pollution causes higher wear and is therefore not covered.

1. The battery is guaranteed for six months. The manufacturer may make the required repair or refuse to 
exchange the defective part if this is possible only at disproportionate cost. In this case, the manufacturer 
turer may remedy the deficiency by means of any other means of subsequent compliance.
Where both types of after -completion are possible only at disproportionate cost, the manufacturer may 
refuse the full after -completion. The customer then has legal claims. Replaced parts shall be transferred 
ferred to the ownership of the manufacturer.
2. By installing spare parts in the context of a warranty case, the warranty period running from delivery of 
of the vehicle to the customer shall not be extended.
3. The warranty shall be without prejudice to wear and tear arising from normal use, as well as wear and 
tear resulting from improper handling and use. Oxidation and corrosion are caused by environmental 
influences and do not constitute a deficiency under the guarantee law.
4. The buyer loses his warranty when manipulating the vehicle, such as modifications to the cable, the 
battery pack, the sensor, the braking system, as well as when installing accessories and spare parts that 
have not been released by the manufacturer.
The loss of warranty entitlement results in all improper interventions, such as by an unskilled workshop, 
as well as non -compliance with maintenance intervals in a specialised workshop.
5. In case of a warranty case, the buyer shall provide the seller with the duly completed service booklet 
including proof of payment.

Only use original MAXMOV accessories and parts.
The use of non -specified accessories may lead to accidents and also to the cancellation of the warranty.

13. Guarantee

14. Accessories Parts

14

Summary of Contents for X2 HUB





















Reviews: