MPC5553/MPC5554 Microcontroller Reference Manual, Rev. 5
Freescale Semiconductor
4-11
4.4.3.2
WKPCFG Pin (Reset Weak Pullup/Pulldown Configuration)
, the signal on the WKPCFG pin determines whether specific eTPU and eMIOS pins
are connected to weak pull up or weak pull down devices during and after reset (see
for the eTPU and eMIOS pins that are affected by WKPCFG). For all reset sources except
the software external reset, the WKPCFG pin is applied starting at the assertion of the internal reset signal
(as indicated by the assertion of RSTOUT). If the WKPCFG signal is logic high at this time, pull up
devices will be enabled on the eTPU and eMIOS pins. If the WKPCFG signal is logic low at the assertion
of the internal reset signal, pull down devices will be enabled on those pins. The value on WKPCFG must
be held constant during reset to avoid oscillations on the eTPU and eMIOS pins caused by switching pull
up/down states. The final value of WKPCFG is latched 4 clock cycles before the negation of RSTOUT.
After reset, software may modify the weak pull up/down selection for all I/O pins through the PCRs in the
SIU.
Also refer to
Chapter 2, “Signal Description
,” for information about the WKPCFG pin.
4.4.3.3
BOOTCFG[0:1] Pins (MCU Configuration)
In addition to specifying the RCHW location, the values latched on the BOOTCFG[0:1] pins at reset are
used to initialize the internal flash memory enabled/disabled state, and whether no arbitration or external
arbitration of the external bus interface is selected. Additionally, the RCHW can determine either directly
or indirectly how the MMU is configured, how the external bus is configured, CAN or eSCI module and
pin configuration, Nexus enabling, and password selection.
Also refer to
Chapter 2, “Signal Description
,” for information about the BOOTCFG pins.
4.4.3.3.1
BOOTCFG[0:1] Configuration in the 208 Package
In the 208 BGA package of the MPC5553, the BOOTCFG0 pin is unavailable and BOOTCFG1 has a
constant value based on PLLCFG0. The device configuration is mapped based on
.
Table 4-6. WKPCFG Settings
WKPCFG
Description
0
Weak pulldown applied to eTPU and eMIOS
pins at reset
1
Weak pullup applied to eTPU and eMIOS
pins at reset
Table 4-7. Boot Configuration in the 208 BGA
PLLCFG0
BOOTCFG1
Boot Identifier
Field
(RCHW)
Boot Mode
Configuration Word Source
0
0
Valid
Internal
The lowest address of one of the six low address
spaces (LAS) in internal flash memory.
Invalid
Serial
Not applicable
1
—
Serial
Not applicable
Summary of Contents for MPC5553
