manualshive.com logo in svg

Freescale Semiconductor MPC561, Reference Manual

The Freescale Semiconductor MPC561 is a powerful microcontroller perfect for embedded systems. For a complete understanding of its capabilities, download the comprehensive Reference Manual for free from 88.208.23.73:8080. This manual provides detailed instructions and information on how to maximize the potential of your MPC561.

Share
Download
background image

Development Support

MPC561/MPC563 Reference Manual, Rev. 1.2

23-14

Freescale Semiconductor

 

When working in the masked mode, all internal breakpoints detected when MSR[RI] = 0 are lost. 
Watchpoints detected in this case are not counted by the debug counters. Watchpoints detected are always 
reported on the external pins, regardless of the value of MSR[RI].

Out of reset, the CPU is in masked mode. Programming the CPU to be in non-masked mode is done by 
setting the BRKNOMSK bit in the LCTRL2 register. Refer to 

Section 23.6.10, “L-Bus Support Control 

Register 2

.” The BRKNOMSK bit controls all internal breakpoints (I-breakpoints and L-breakpoints).

23.2.1.5

Ignore First Match

In order to facilitate the debugger utilities “continue” and “go from x”, the ignore first match option is 
supported for instruction breakpoints. When an instruction breakpoint is first enabled (as a result of the 
first write to the instruction support control register or as a result of the assertion of MSR[RI] when 
operating in the masked mode), the first instruction will not cause an instruction breakpoint if the ignore 
first match (IFM) bit in the instruction support control register (ICTRL) is set (used for “continue”). 

When the IFM bit is clear, every matched instruction can cause an instruction breakpoint (used for “go 
from x”). This bit is set by the software and cleared by the hardware after the first instruction breakpoint 
match is ignored. Load/store breakpoints and all counter generated breakpoints (instruction and load/store) 
are not affected by this mode.

23.2.1.6

Generating Six Compare Types

Using the four compare types mentioned above (equal, not equal, greater than, less than) it is possible to 
generate also two more compare types: greater than or equal and less than or equal.

•

Generating the greater than or equal compare type can be done by using the greater than compare 
type and programming the comparator to the needed value minus 1.

•

Generating the less than or equal compare type can be done by using the less than compare type 
and programming the comparator to the needed value plus 1.

This method does not work for the following boundary cases:

•

Less than or equal of the largest unsigned number (1111...1)

•

Greater than or equal of the smallest unsigned number (0000...0)

•

Less than or equal of the maximum positive number when in signed mode (0111...1)

•

Greater than or equal of the maximum negative number when in signed mode (1000...)

These boundary cases need no special support because they all mean ‘always true’ and can be programmed 
using the ignore option of the load/store watchpoint programming (refer to 

Section 23.2, “Watchpoints and 

Breakpoints Support

”).

23.2.2

Instruction Support

There are four instruction address comparators A,B,C, and D. Each is 30 bits long, generating two output 
signals: equal and less than. These signals are used to generate one of the following four events: equal, not 
equal, greater than, less than.

Summary of Contents for MPC561













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC561

IAI ROBO Cylinder RCP2 Series Quick Start Manual preview
ROBO Cylinder RCP2 Series
Brand: IAI Pages: 5
RADEMACHER Troll Comfort Mounting And Operating Instruction preview
Troll Comfort
Brand: RADEMACHER Pages: 68
ZKTeco IN710 Quick Start Manual preview
IN710
Brand: ZKTeco Pages: 11
EFI E-42 Installation And Service Manual preview
E-42
Brand: EFI Pages: 127
maxxess eMAX-EP4502 Installation Manual preview
eMAX-EP4502
Brand: maxxess Pages: 11
SOLARJACK PVA 5-30 User Manual preview
PVA 5-30
Brand: SOLARJACK Pages: 14
VMK VMK-I49plus Instruction Manual preview
VMK-I49plus
Brand: VMK Pages: 98
Halma Alicat Scientific MC Quick Start Manual preview
Alicat Scientific MC
Brand: Halma Pages: 2
Xylem Aquavar IPC Quick Start Manual preview
Aquavar IPC
Brand: Xylem Pages: 28
Overland Storage NEO 2000e Remove & Replace Instructions preview
NEO 2000e
Brand: Overland Storage Pages: 4
ICON ProCon C700 Series Operating Manual preview
ProCon C700 Series
Brand: ICON Pages: 30
ICP DAS USA CAN-8124 User Manual preview
CAN-8124
Brand: ICP DAS USA Pages: 153
H3C WX1804H-PWR Quick Start Manual preview
WX1804H-PWR
Brand: H3C Pages: 15
Dräger REGARD-1 Installation, Operation And Maintenance Manual preview
REGARD-1
Brand: Dräger Pages: 48
Sierra Wireless AirPrime MC7350 Hardware Integration Manual preview
AirPrime MC7350
Brand: Sierra Wireless Pages: 20
Danfoss AMD 610 AS Installation Manual preview
AMD 610 AS
Brand: Danfoss Pages: 2
VubIQ V60WGD03 User Manual preview
V60WGD03
Brand: VubIQ Pages: 17
Festo VPPM Series Operating Instructions Manual preview
VPPM Series
Brand: Festo Pages: 48

Brands by name

Popular brands

Load more brands