Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 417 / 1374

background image

Memory Management Unit (MMU)

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

11-3

Hardware data and program access protection is defined for each data/program memory
region for two privilege levels: user and supervisor. The MMU provides abort signals for
the Xa/Xb/P buses for errant accesses. The MMU provides memory region support, as
follows:

— For the program memory region: Provides supervisor-level read allowed/not allowed

access; for the User level, provides read allowed/not allowed access

— For the data memory region: Provides read/write allowed/not allowed for both the

Supervisor and User levels

Address translation is defined for each data/program memory region, enables allocating
virtual memory region to a valid physical memory space.

Priority mechanism between descriptors, allowing memory regions overlapping.

Stores the program task ID and data task ID for multi-task mechanism. Up to 255 different
Program IDs and 255 different data IDs are available.

General Purpose registers among its control and status registers.

Access error detection including non-mapped memory access and misaligned memory
access.

Captures error status bits and enables a fast error diagnostic.

Precise interrupts allowing handling MMU MATT misses supporting a virtually paged
operating system.

Core branch target buffer (BTB) that enables manual and automatic BTB maintenance.

Platform error detection code (EDC) recovery scheme.

Enable/disable EDC exception mechanism.

Peripherals error handling.

«
...
415
416
417
418
419
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Univerge SV8100

Brand: NEC Pages: 44

Brand: Data Translation Pages: 60

Brand: N.A.T. Pages: 32

PoleVault System A/V Source Inputs

Brand: Extron electronics Pages: 4

Brand: ZyXEL Communications Pages: 215

Brand: Supero Pages: 16

Brand: Freescale Semiconductor Pages: 8

NVRx-7300 series

Brand: Swann Pages: 9

Brand: Taiwan Commate Computer Inc. Pages: 25

Brand: Greenlee Pages: 52

Brand: ExtraHop Pages: 2

Brand: Valcom Pages: 4

Brand: Jabra Pages: 2

Brand: Vivotek Pages: 185

VOYIX 7772-K141

Brand: NCR Pages: 10

Brand: Olivella Modular Pages: 19

Brand: StarTech.com Pages: 10

ASMB-816 Series

Brand: Advantech Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands