Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 477 / 1374

background image

Set-Up and Initialization

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

12-25

The final error the memory controller detects is the automatic calibration error. This error is set if
the memory controller detects an error during its training sequence.

12.6

Set-Up and Initialization

System software can configure the DDR memory controller. The DDR memory controller uses
its bank map to assert the appropriate

MCS[0–1]

signal for memory accesses according to the

provided bank depths. System software also configures the DDR memory controller at system
start-up to multiplex the row and column address bits for each bank (see Table 12-17 on page
12-33). Address multiplexing occurs according to these configuration bits. At system power-up,
initialization software (boot code, for example) must set up the programmable parameters in the
memory interface configuration registers listed in Table 12-13.

Note:

1.

Before initiating the DDR controller registers the DDR_GCR[DDR_VSEL] should be
programmed according to the DDR device connected to the MSC8144. For DDR1
devices the DDR_GCR[DDR_VSEL] = 0 (reset value), for DDR2 devices the
DDR_GCR[DDR_VSEL] = 1 Programming the correct value is essential for the correct

Table 12-12. Memory Controller Errors

Category

Error

Descriptions

Action

Detect Register

Notification

Single-bit ECC
threshold

The number of ECC errors has reached the
threshold specified in the ERR_SBE.

The error is reported
via critical interrupt if
enabled.

The error control
register logs only
read versus
write, not full
type

Access
Error

Multi-bit ECC
error

A multi-bit ECC error is detected during a read,
or read-modify-write memory operation.

Memory select
error

Read, or write, address does not fall within the
address range of any of the memory banks.

Training Calibration

error

One of the calibration processes executed
during the initialization failed

«
...
475
476
477
478
479
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: Palm Pages: 4

Brand: SIIG Pages: 12

Brand: Quectel Pages: 23

Brand: Bridgeworks Pages: 18

MegaRAID SATA 300-4XLP

Brand: LSI Pages: 3

ER3-100 (5K02-55)

Brand: 8e6 Technologies Pages: 74

Brand: Valcom Pages: 4

Brand: 3Com Pages: 12

Brand: Vega Pages: 12

Brand: Cypress Semiconductor Pages: 26

Brand: PairGain Pages: 48

SPEEDTOUCH 110G

Brand: THOMSON Pages: 26

Brand: Sony Ericsson Pages: 2

CamCon FCS-4000

Brand: LevelOne Pages: 94

Brand: Alcatel-Lucent Pages: 8

Brand: National Instruments Pages: 37

Brand: Iomega Pages: 32

C32C824151 - UB E02 Print Server

Brand: Epson Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands