Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 479 / 1374

background image

Set-Up and Initialization

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

12-27

12.6.1

Programming Differences Between Memory Types

Depending upon the memory type, certain fields must be programmed differently. Table 12-14
illustrates the differences in certain fields for different memory types. This table does not list all
fields that must be programmed.

Note:

Before initiating the DDR controller registers the DDR_GCR[DDR_VSEL] should be
programmed according to the DDR device connected to the MSC8144. For DDR1
devices the DDR_GCR[DDR_VSEL] = 0 (reset value), for DDR2 devices the
DDR_GCR[DDR_VSEL] = 1 Programming the correct value is essential for the
correct operation of the DDR interface, since it defines to the I/O cells the selected
operating voltage.

DDR SDRAM Control
Configuration Register 2
(DDR_SDRAM_CFG_2)

Force Self Refresh (FRC_SR)
DLL Reset Disable (DLL_RST_DIS)
DQS Configuration (DQS_CFG)
ODT Configuration (ODT_CFG)
Number of Posted Refreshes (NUM_PR)
DRAM Data Initialization (D_INIT)

Table 12-23 on
page 12-45

DDR SDRAM Mode
Configuration Register
(DDR_SDRAM_MODE)

Extended SDRAM Mode (ESDMODE)
SDRAM Mode (SDMODE)

Table 12-24 on
page 12-46

DDR SDRAM Mode
Configuration 2 Register
(DDR_SDRAM_MODE_2)

Extended SDRAM Mode 2 (ESDMODE2)
Extended SDRAM Mode 3 (ESDMODE3)

Table 12-25 on
page 12-47

DDR SDRAM Interval
Configuration Register
(DDR_SDRAM_INTERVAL)

Refresh Interval (REFINT)
Precharge Interval (BSTOPRE)

Table 12-27 on
page 12-49

DDR SDRMA Data
Initialization Register

Initialization Value (IVAL)

Table 12-28 on
page 12-50

DDR SDRAM Clock Control
Configuration Register
(DDR_SDRAM_CLK_CNTL)

Clock Adjust (CLK_ADJUST)

Table 12-29 on
page 12-51

DDR Initialization Address
Register
(DDR_INIT_ADDRESS)

Initialization Address (IADDR)

Table 12-30 on
page 12-52

Table 12-14. Programming Differences Between Memory Types

Parameter

Description

Differences

Page

AP_x_EN

Chip Select x Auto
Precharge Enable

DDR1

Can be used to place chip select x into auto
precharge mode.

Table 12-17 on
page 12-33

DDR2

Table 12-13. Memory Interface Configuration Register Initialization Parameters (Continued)

Register

Parameter Bits

Page

«
...
477
478
479
480
481
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: Barco Pages: 100

Netlink FRX8000

Brand: Cabletron Systems Pages: 94

MMAC-Plus 9E423-24

Brand: Cabletron Systems Pages: 10

MMAC-Plus 9A128-01

Brand: Cabletron Systems Pages: 22

Spectrum EMM-E6

Brand: Cabletron Systems Pages: 2

Brand: Cabletron Systems Pages: 54

Cabletron BRIM-F6

Brand: Cabletron Systems Pages: 43

Netlink FRX4000

Brand: Cabletron Systems Pages: 60

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

Brand: Laird Pages: 36

Brand: Palo Alto Network Pages: 56

Brand: SAF Pages: 30

Brand: Accusys Pages: 34

SABVISION NVR32

Brand: SAB Pages: 29

Brand: DigiTech Pages: 6

Brand: Xenteq Pages: 16

Brand: Maxtor Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands