Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 482 / 1374

background image

MSC8144E Reference Manual, Rev. 3

12-30

Freescale

Semiconductor

DDR SDRAM Memory Controller

Table 12-15 illustrates the steps the DDR controller will follow when using this automatic
hardware initialization. If the bypass initialization mode is used, then software can initialize the
memory through the DDR_SDRAM_MD_CNTL register.

12.7

Memory Controller Programming Model

In the register figures and field descriptions, the following access definitions apply:

Reserved fields are always ignore for the purposes of determining access type.

Read/write, read only, and write only (R/W, R, and W, respectively) indicate that all the
non-reserved fields in a register have the same access type.

Non-reserved fields that are cleared by writing 1s to them are indicated by w1c.

Mixed indicates a combination of access types.

Special is used when no other category applies. For special access registers, read the figure
and field descriptions very carefully.

The DDR memory controller registers are as follows:

Chip-Select Memory Bounds Register (CSx_BNDS), page 12-32.

Chip-Select Configuration Register (CSx_CONFIG), page 12-33.

DDR SDRAM Extended Refresh Recovery Register (TIMING_CFG_3), page 12-34.

DDR SDRAM Timing Configuration 0 Register (TIMING_CFG_0), page 12-35.

DDR SDRAM Timing Configuration 1 Register (TIMING_CFG_1), page 12-38.

DDR SDRAM Timing Configuration 2 Register (TIMING_CFG_2), page 12-40.

DDR SDRAM Control Configuration Register (DDR_SDRAM_CFG), page 12-42.

DDR SDRAM Control Configuration 2 Register (DDR_SDRAM_CFG_2), page 12-44.

DDR SDRAM Mode Configuration Register (DDR_SDRAM_MODE), page 12-46.

DDR SDRAM Mode Configuration 2 Register (DDR_SDRAM_MODE_2), page 12-47.

Table 12-15. DRAM Initialization Requirements

DDR1

DDR2

CKE low at POR

CKE low at POR

NOP w/CKE high

NOP w/CKE high

Wait 400 ns (200 cycles)

PRE_ALL

PRE_ALL

EMRS(2)

EMRS(3)

EMRS (en DLL)

EMRS (en DLL)

MRS (DLL reset)

MRS (DLL reset)

PRE_ALL

PRE_ALL

AUTO REFRESH

AUTO REFRESH

AUTO REFRESH

AUTO REFRESH

MRS (w/o DLL reset)

MRS (w/o DLL reset)

Wait 200 clocks

Wait 200 clocks

Set OCD Disabled

«
...
480
481
482
483
484
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: C4i Pages: 8

Brand: TC Electronic Pages: 55

Brand: ebm-papst Pages: 16

Brand: Oracle Pages: 24

Compact Emulator M30620T-CPE

Brand: Renesas Pages: 52

Brand: Dolphin Pages: 9

Brand: Kanguru Pages: 13

Brand: Kaya Instruments Pages: 48

LL140 RGB Series

Brand: Corsair Pages: 30

VAR-SOM-MX8M-PLUS

Brand: Variscite Pages: 2

Brand: ETAS Pages: 68

WAFER-EHL Series

Brand: IEI Technology Pages: 142

Brand: RadioSPECTRAL Pages: 2

Brand: ZALMAN Pages: 9

Brand: Cutting Edge Pages: 92

Brand: SilverStone Pages: 16

PC/104-PCMCIA-1

Brand: Kontron Pages: 20

Brand: Agilent Technologies Pages: 458

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands