manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at 88.208.23.73:8080.

Share
Download
background image

MSC8144E Reference Manual, Rev. 3

26-62

 Freescale 

Semiconductor

Security Engine (SEC)

26.4.6.12   KEU IV_2 Register (Fresh)

The fresh value in the KEU IV_2 register is used during the initialization phase of the 3GPP F9 
algorithm. This value is ignored when the F8 algorithm is selected. The fresh value must be 
written before a new message to be processed with 3GPP F9 is started. Once the initialization 
phase is completed, the KEU IV_2 register is no longer used during message processing. You do 
not need to write the KEU IV_2 register during context switches. 

26.4.6.13   KEU Context Data Registers

There are six 64-bit KEU context data registers that allow the core processor to read/write the 
contents of the context used to process the message. The KEU context data registers must be read 
when changing context and restored to their original values to resume processing an interrupted 
message. For F8 and 3GPP F9 modes, all six 64-bit KEU context data registers must be read to 
retrieve context, and all 6 must be written back to restore context. The context must be written 
prior to the key data. If the any of the KEU context data registers are written during message 
processing, a context error will be generated. All KEU context data registers are cleared when a 
hard/soft reset or initialization is performed.

Note:

In typical operation, a frame is received and processed in its entirety, with the KEU 
performing session specific initialization using the contexts of KEU IV_1 and IV_2 
registers. The KEU context data and IV_1 registers should only be unloaded/reloaded 
when the processing of a frame is discontinued prior to completion, then processing is 
resumed. 

26.4.6.14   KEU Key Data Registers_[1–2] (Confidentiality Key)

The first pair of KEU Key data registers together hold one 128-bit key used for F8 encryption/ 
decryption. KEU Key Data Register_1, (CK-high), holds the first 8 bytes (1–8). KEU Key Data 
Register_2, (CK-low), holds the second 8 bytes (9–16). The KEU Key Data Registers must be 
written before message processing begins. Writing a register while the block is processing data, 
generates a context error. Reading from either of these registers results in an address error being 
reflected in the KEU Interrupt Status Register.

26.4.6.15   KEU Key Data Registers _[3–4] (Integrity Key)

The second pair of KEU Key Data Registers together hold one 128-bit key that is used for F9 
message authentication. KEU Key Data Register_3, (IK-high) holds the first 8 bytes (1–8). KEU 
Key Data Register_4, (IK-low), holds the second 8 bytes (9–16). The KEU Key Data Registers 
must be written before message processing begins. Writing a register while the block is 
processing data generates a context error.

If the ‘F9 only’ mode is set, the integrity key data can optionally be written to KEU Key Data 
Registers_[1–2]. This eliminates the need for the core processor to offset from the base key 

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

NEC Univerge SV8100 System Configuration Manual preview
Univerge SV8100
Brand: NEC Pages: 44
TC Electronic DB6 User Manual preview
DB6
Brand: TC Electronic Pages: 174
TC Electronic Finalizer Express User Manual preview
Finalizer Express
Brand: TC Electronic Pages: 33
Omega Engineering OME-A8111 Hardware Manual preview
OME-A8111
Brand: Omega Engineering Pages: 34
Roland VP-9000 Turbostart preview
VP-9000
Brand: Roland Pages: 2
Realtek RTL8187SE User Manual preview
RTL8187SE
Brand: Realtek Pages: 30
Enterasys Enterasys Matrix 2G4082-25 Hardware Installation Manual preview
Enterasys Matrix 2G4082-25
Brand: Enterasys Pages: 58
Supero AOC-1UIPMI-B User Manual preview
AOC-1UIPMI-B
Brand: Supero Pages: 53
FiberHome AN5506-04-F User Manual preview
AN5506-04-F
Brand: FiberHome Pages: 2
Bridgeworks Tamar FCSAS102800 User Manual preview
Tamar FCSAS102800
Brand: Bridgeworks Pages: 56
JAKA MiniCab Hardware User Manual preview
MiniCab
Brand: JAKA Pages: 37
Renesas H8S/2646 Series User Manual preview
H8S/2646 Series
Brand: Renesas Pages: 20
Teridian 71M6533 Quick Start Manual preview
71M6533
Brand: Teridian Pages: 2
Echelon i.LON SmartServer Hardware Manual preview
i.LON SmartServer
Brand: Echelon Pages: 34
A.E.B. ARCHIMEDE Fitting Instructions And Warranty Workbook preview
ARCHIMEDE
Brand: A.E.B. Pages: 28
S&T Kontron CP3005 Series User Manual preview
Kontron CP3005 Series
Brand: S&T Pages: 115
Intel Braswell Series Technical Manual preview
Braswell Series
Brand: Intel Pages: 54
El.Mo 090010932 User Manual preview
090010932
Brand: El.Mo Pages: 16

Brands by name

Popular brands

Load more brands