Freescale Semiconductor PXR4030 Reference Manual Download | Manualshive

Page: 1073 / 1434

background image

Enhanced Queued Analog-to-Digital Converter (EQADC)

Freescale Semiconductor

27-91

PXR40 Microcontroller Reference Manual, Rev. 1

Figure 27-59. Non-coherency Detection when Transfers from a Command Sequence are Interrupted

27.7.5

EQADC Result FIFOs

27.7.5.1

RFIFO Basic Functionality

There are six RFIFOs located in the EQADC. Each RFIFO is four entries deep, and each RFIFO entry is
16 bits long. Each RFIFO serves as a temporary storage location for the one of the RQueues allocated in
system memory. Result data is saved in the RFIFOs before being moved into the system RQueues. When
an RFIFO is not empty, the EQADC sets the corresponding RFDF bit in

Section 27.6.2.7, EQADC FIFO

and Interrupt Status Registers (EQADC_FISR)

. If RFDE is asserted in

Section 27.6.2.6, EQADC Interrupt

and DMA Control Registers (EQADC_IDCR)

, the EQADC generates a request so that an RFIFO entry is

moved to the RQueue. An interrupt request, served by the host CPU, is generated when RFDS is negated,
and a DMA request, served by the DMAC, is generated when RFDS is asserted. The host CPU or the
DMAC responds to these requests by reading

Section 27.6.2.4, EQADC Result FIFO Pop Registers

, to retrieve data from the RFIFO.

NOTE

The DMAC should be configured to read a single result (16-bit data) from
the RFIFO pop registers for every asserted DMA request it acknowledges.
Refer to

Section 27.8.2, EQADC/DMAC Interface

configuration guidelines.

NOTE

Reading a word, a half-word, or any bytes from EQADC_RFPRx will pop
an entry from RFIFOx, and the RFCTRx field will be decremented by one.

describes the important components in the RFIFO. Each RFIFO is implemented as a circular

set of registers to avoid the need to move all entries at each push/pop operation. The Pop Next Data Pointer
always points to the next RFIFO message to be retrieved from the RFIFO when reading EQADC_RFPR.

CF5_CB1_CM0

CF5_CB1_CM1

CF5_CB1_CM2

CF5_CB1_CM3

CF5_CB1_CM4

CF5_CB1_CM5

CF5_CB1_CM6

CF5_CB1_CM7

CF5_CB1_CM8

CF5_CB1_CM9

CF5_CB1_CM10

CF5_CB1_CM11

CF5_CB1_CM12

CF5_CB1_CM13

Command sequence became non-coherent before command 4
was transferred. Once command transfers are resumed, EQADC
will only check for coherency after command 4.

Command sequence became non-coherent before command 11
was transferred. Once command transfers are resumed, EQADC
will only check for coherency after command 11.

«
...
1071
1072
1073
1074
1075
...
»

Summary of Contents for PXR4030



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PXR4030

Brand: Vacon Pages: 62

Brand: Gardena Pages: 14

Brand: Gardena Pages: 4

GAT ACCESS 6100

Brand: Gantner Pages: 4

Brand: Parkside Pages: 65

Brand: Rain Bird Pages: 4

Brand: Rain Bird Pages: 2

Brand: Rain Bird Pages: 140

WeatherSmart RSC600i

Brand: Raindrip Pages: 36

J1000 CIMR-JC series

Brand: YASKAWA Pages: 26

Brand: Purmo Pages: 2

Brand: salmson Pages: 78

Brand: D+H Pages: 16

Brand: Anilam Pages: 31

Brand: Kelly Pages: 32

Brand: Vector Pages: 22

Brand: Holars AS Pages: 15

Brand: Maintronic Pages: 53

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands