Freescale Semiconductor PXR4030 Reference Manual Download | Manualshive

Page: 662 / 1434

background image

FlexRay Communication Controller (FLEXRAY)

22-78

Freescale Semiconductor

PXR40 Microcontroller Reference Manual, Rev. 1

Each individual message buffer consists of two parts, the physical message buffer, which is located in the
flexray memory, and the message buffer control data, which are located in dedicated registers. The
structure of an individual message buffer is given in

.

Each individual message buffer has a message buffer number n assigned, which determines the set of
message buffer control registers associated to this individual message buffer. The individual message
buffer with message buffer number

n

is controlled by the registers MBCCSRn, MBCCFRn, MBFIDRn,

and MBIDXRn.

The connection between the message buffer control registers and the physical message buffer is
established by the message buffer index field MBIDX in the

Message Buffer Index Registers (MBIDXRn)

.

The start address SADR_MBHF of the related message buffer header field in the flexray memory is
determined according to

SADR_MBHF = (MBIDXRn[MBIDX] * 10) + SMBA

Eqn. 22-3

Figure 22-104. Individual Message Buffer Structure

22.6.3.1.1

Individual Message Buffer Segments

The set of the individual message buffers can be split up into two message buffer segments using the

Message Buffer Segment Size and Utilization Register (MBSSUTR)

. All individual message buffers with

a message buffer number n <= MBSSUTR[LAST_MB_SEG1] belong to the first message buffer segment.
All individual message buffers with a message buffer number n > MBSSUTR[LAST_MB_SEG1] belong
to the second message buffer segment. The following rules apply to the length of the message buffer data
field:

•

all physical message buffers associated to individual message buffers that belong to the same
message buffer segment must have message buffer data fields of the same length

•

the minimum length of the message buffer data field for individual message buffers in the first
message buffer segment is 2 * MBDSR[MBSEG1DS] bytes

•

the minimum length of the message buffer data field for individual message buffers assigned to the
second segment is 2 * MBDSR[MBSEG2DS] bytes.

MBFIDRn

Message Buffer Control Registers

MBCCSRn

MBCCFRn

MBIDXRn

(min) MBDSR[MBSEG1DS] * 2 bytes / MBDSR[MBSEG2DS] * 2 bytes

Data Field Offset

Frame Data

Message Buffer Header Field

Message Buffer Data Field

Slot Status

Frame Header

SADR_MBDF

SADR_MBHF

Fl

e

x

Ra

y Memor

y

«
...
660
661
662
663
664
...
»

Summary of Contents for PXR4030



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PXR4030

Brand: Oldham Pages: 32

Brand: Harmonic Drive Pages: 85

Brand: Eaton Pages: 96

Brand: J+J Pages: 2

FX-COMM4NDER MFX3203

Brand: Magicfx Pages: 16

Brand: Procom Pages: 10

Brand: Sullair Pages: 31

Brand: Woodward Pages: 32

Brand: YASKAWA Pages: 42

Brand: YASKAWA Pages: 351

Brand: Gardena Pages: 15

Brand: Digiplex Pages: 48

Brand: Kelly Pages: 37

Brand: Danfoss Pages: 4

Brand: D-M-E Pages: 15

Brand: Alcor Micro Pages: 18

TRILOGY T500 Series

Brand: Eclipse Pages: 20

MotorController WCC 310 UL

Brand: Window Master Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands