Descriptions of LEFT and RIGHT are from the point of view of standing
behind the equipment facing the front
15
ASSEMBLY DIAGRAM 10
USE A PARTNER TO HELP WITH THIS STEP
REMEMBER: Only hand tighten all nuts and bolts until whole
&&Ͳ
X
ϰ
is assembled
(HINT: Work your way from the stoppered end of the cable to the other, connecting one pulley at a time and ensuring
everything is positioned correctly before continuing. Ensure the cable retainers are all correctly angled)
1.
Position the stopped end of the UPPER CABLE (43) underneath the front of the UPPER FRAME (4), draw the rest of the
cable up through the pulley bracket.
2.
Insert a PULLEY (79) into the pulley bracket, ensuring the cable runs up the front and over the pulley. Attach using a
HEX BOLT M10X85 (108), two WASHER10 (92) and an AIRCRAFT NUT M10 (97)
3.
Draw the cable along and down through the next pulley bracket on the UPPER FRAME (4)
4.
Insert a PULLEY (79) into the pulley bracket, ensuring the cable runs over the top and down the back of the pulley.
Attach using a HEX BOLT M10X85 (108), two WASHER10 (92) and an AIRCRAFT NUT M10 (97)
5.
Draw the cable forward through the top of the FRONT PRESS BASE (9)
6.
Slide an ALLEN BOLT M10X190 (112) through a WASHER10 (92) and into the top right hole of the FRONT PRESS BASE
(9). Feed onto the bolt (in correct order), two WASHER10 (92), two CABLE RETAINER (86), two CABLE RETAINER
BUSHING (85) and a PULLEY (79). Slide the bolt out the top left hole, secure using a WASHER10 (92) and an AIRCRAFT
NUT (97)
7.
Ensure the cable runs over the top of the pulley, then draw the cable backward into the pulley bracket on the FRONT
VERTICAL FRAME (3)
DIAGRAM C
8.
Insert a PULLEY (79) into the bracket, ensuring the cable runs over and down the rear of the pulley. Using a HEX BOLT
M10X55 (103), connect a WASHER10 (92), a CABLE RETAINER (86), and a CABLE RETAINER BUSHING (85) to both
outer sides of the pulley bracket. Secure the whole assembly with an AIRCRAFT NUT M10 (97)
9.
Draw the cable forward again, through the FRONT PRESS BASE (9)
10. Slide an ALLEN BOLT M10X190 (112) through a WASHER10 (92) and into the lower right hole of the FRONT PRESS
BASE (9). Feed onto the bolt (in correct order), two WASHER10 (92), two CABLE RETAINER (86), two CABLE RETAINER
BUSHING (85) and a PULLEY (79). Slide the bolt out the lower left hole, secure using a WASHER10 (92) and an
AIRCRAFT NUT (97)
11. Ensure the cable runs over the top of the pulley, then draw the cable under and backward and feed it through the
pulley slot on the FRONT VERTICAL FRAME (3)
DIAGRAM C
12. Insert a PULLEY (79) into the slot ensuring the cable runs over the top of the pulley. Attach using a HEX BOLT M10X65
(104), two PULLEY BUSHING (83) and an AIRCRAFT NUT M10 (97)
13. Assemble the two hanging pulley brackets
DIAGRAM A & B.
For each,
i
nsert a PULLEY (79) into the top bolt holes of
ADJUSTABLE PULLEY BRACKET (17).Using a HEX BOLT M10X55 (103), connect a WASHER10 (92), a CABLE RETAINER
(86), and a CABLE RETAINER BUSHING (85) to both outer sides of the pulley bracket. Secure the whole assembly with
an AIRCRAFT NUT M10 (97). Ensuring correct orientation, attach them to the two pre-positioned ADJUSTABLE BOLTS
(28) under the upper frame.
14. Draw the cable downward and feed it under the assembled hanging pulley
A
15. Draw the cable upward to the pulley bracket under the rear of the UPPER FRAME (4)
DIAGRAM D
. Insert a PULLEY
(79) into the pulley bracket. Using a HEX BOLT M10X80 (107), connect a WASHER10 (92), a CABLE RETAINER (86), and
a CABLE RETAINER BUSHING (85) to the left outer side of the pulley bracket. Leave the other side bare and unsecured
until the next stage of assembly in
STEP 11
16. Ensure the cable runs over the top of the pulley, then draw the cable downward and feed it under the assembled
hanging pulley
B
17. Draw the cable up into the pulley bracket under the UPPER GUIDE ROD FRAME (8). Insert a PULLEY (79) into the
pulley bracket. Using a HEX BOLT M10X55 (103), connect a WASHER10 (92), a CABLE RETAINER (86), and a CABLE
RETAINER BUSHING (85) to both outer sides of the pulley bracket. Secure the whole assembly with an AIRCRAFT NUT
M10 (97). Ensure the cable runs over the pulley from right to left.
18. Draw the cable downwards, pass it through the ring on the end of the WEIGHT SELECTOR PIN (62) and connect the
end to the top of the SELECTOR ROD (73)
