background image

Cool-Spot in operation

User Manual

Cool-Spot.nl

9

4. Attention! Display notifications, explanation and desired actions

Displays  

Interim Defrost Cycle:
The refrigeration unit has become partially frozen, reducing the 
amount of cold air on the top. System only temporarily switches 
off the refrigeration unit. System switches on when cooler is 
defrosted. In the event of a recurring message:

Actie: 

Press the 

P button for at least 10 seconds to start the defrost 

cycle manually.
 

High pressure cooling, Temperature fault 
Reset Refrigeration unit:
This message will only appear on the display of CS refrigeration 
units that have an internal condensing unit or an external ZG 
Remote Condenser.
Due to insufficient cooling of the condensing unit or of the 
Remote Condenser, the pressure relief valve switches off the 
cooling compressor.

 

 

Low pressure cooling Temp fault auto reset: 
This message is only for CS refrigeration units with internal 
condensing unit. This fault resets automatically; if this message 
regularly appears, the CS system probably has a shortage of 
refrigerant.

Action: 

Call/email service.

C

ool

s

pot

NL

R

FRESH  TECHNOLOGY

C

ool

s

pot

NL

R

FRESH  TECHNOLOGY

CoolSpot 

®

On

Attention  !
Interim
Defrost cycle

C

ool

s

pot

NL

R

FRESH  TECHNOLOGY

CoolSpot 

®

on

Low pressure
cooling
malfuntion
auto reset

CoolSpot 

®

On

Attention  !
High pressure cooling
Temperature failure
Reset cooling unit

Causes:

Insufficient supply of cooling 
water due to insufficient water 
pressure. The water pressure 
has temporarily dropped due 
to e.g. work being carried out 
in the building. In the case of 
a remote condenser, the fan 
has failed, is defective or the 
cooler is dirty.

Action 1: 

check the water pressure/ 
water supply. For remote coo-
lers: check fan operation and/
or remove contamination from 
cooler. Check the fuse for the 
power supply to the fan

Action 2: 

Reset condensing unit pressu-
re relief valve with push button 
by firmly pressing black but-
ton manually. If this message 
recurs, call your own Technical 
Department or Cool-Spot 
service department.

Summary of Contents for Cool-Spot

















Reviews: