Friedrich CCW06B10B, Operating Instructions Manual

13

1

2

3

3

4

5

6

7

8

9

1.

Power

: Turn the air conditioner on and off. This button will 

clear the TIMER setting.

2. 

MODE:

 Press the button to select the mode of operation, AUTO, COOL, 

DRY, FAN ONLY, HEAT.

Note: 

The HEAT mode is only for some heating models. If you do not 

need it, press the MODE button for more than 5 seconds to delete the 
HEAT function, and the COOL mode will be selected automatically. 
Press the MODE again for more than 5 seconds to add the HEAT 
function, and the HEAT mode will be selected automatically. 

3.      And      : Use these buttons to increase or decrease the setting 
    Temperature or Timer. Setting temperature range: 61 ~88

 or 16 ~31

.

Note:

 When the remote controller is turn-off, press       and      buttons can 

    pre-set the temperature. After the setting, the remote temperature display 
    will be off after a while.

4. 

TURBO:

 When the remote is ON, press the button to active the TURBO 

function, under AUTO/COOL/FAN ONLY mode. Press again to cancel the 
TURBO function, and the fan speed will change to pre-setting before.

Note:

 and 

 change: After insert the batteries, in the off state within 3 

minutes, press the TURBO button for more than 5 seconds to switch the 
Fahrenheit (

) or Celsius (

) degree display. 

5. 

DISPLAY:

 When the unit is ON, press the button, to switch off/on all lights 

or LED display. And this function will be canceled when changing mode.

6. 

TIMER:

 Use the button to set the TIMER, or cancel the TIMER.

TIMER OFF:

 When the unit is ON, the timed OFF is programmed by 

pressing TIMER button, the remote will display 6 hours pre-setting at first. 
Set the rest time by pressing the button      or      until the needed rest time 
display, then press TIMER button again to confirm.

TIMER ON:

 When the unit is OFF, the timed ON is programmed by pressing 

TIMER button, the remote will display 6 hours pre-setting at first. Set the 
rest time by pressing the button      or      until the needed rest time display, 
then press TIMER button again to confirm. Later, the remote screen will keep 
display [

TIMER

] icon.

Note:

 When TIMER ON, it cannot select Sleep mode, but can pre-set Mode, 

temperature, fan speed, MONEY SAVER. 

7. 

SLEEP: 

Press the SLEEP button, all of the display lights will turn off after a 

while, but the Sleep light is always on. In SLEEP mode, the air conditioner 
will automatically adjust the temperature and fan speed to make the room 
more comfortable. The set temperature will automatically change every 30-
60 minutes and at most change six times until the setting temperature is 81 
or 82

 for cooling mode and 75 or 76

 for heating mode.. 

8. 

FAN

SPEED:

 Press the FAN SPEED button to choose the fan speed options. 

You can choose Hi, Med, Lo or Auto speed in COOL or HEAT mode and 
choose Hi, Med, Lo in FAN mode. When DRY mode, it is only Low fan speed.

9. 

MONEY SAVER:

 When the unit is in COOL mode, press the button to 

MONEY SAVER function. In MONEY SAVER mode, the unit will turn off 
once the room is cooled to the user set temperature. The unit will turn back 
on when the room temperature rises above the user set temperature. Before 
the compressor starts, the fan motor will run for a while, then it will stop for 
a while, and will repeat to provide a much more comfortable feeling and 
save energy.

10. 

Child Lock:

 pressing the button      or      for more than 2 seconds to lock 

      or unlock the remote controller. When locked, each function button is no 
      useful, and the lock icon will flash when press any button.

+

-

+

-

+ -

+ -

+ -