33
PB
OPERATION
9-24k Sequence of Operation
1.Basic function of system
(1)Cooling mode
(2)Drying mode
(1) Under this mode, fan and swing operates at setting status. Temperature setting range is 60.8~86.0
O
F.
(2) During malfunction of outdoor unit or the unit is stopped because of protection, indoor unit keeps original operation status.
(3)Heating mode
(1) Under this mode, fan operates at low speed and swing operates at setting status. Temperature setting range is 60.8~86.0
O
F.
(2) If the outdoor unit malfunctions, or the unit is stopped because of protection, indoor unit keeps original operation status.
(3) Protection status is same as that under cooling mode.
(4) Sleep function is not available for drying mode.
(1) Under this mode, Temperature setting range is 60.8~86.0
O
F.
(2) Working condition and process for heating mode:
When unit heating mode is turned on, the indoor unit enters into cold air prevention status. When the unit is stopped or at OFF status,
and indoor unit has been initially started, the unit enters into residual heat-blowing status.
a. During cooling operation, protection function is same as that under cooling mode.
b. During heating operation, protection function is same as that under heating mode.
(4)Working method for AUTO mode:
1.Working condition and process for AUTO mode:
a.Under AUTO mode, standard heating Tpreset=68.0
O
F and standard cooling Tpreset=77.0
O
F. The unit will switch mode automatically
according to ambient temperature.
2.Protection function
3. Display: Set temperature is the set value under each condition. Ambient temperature is (Tamb.-Tcompensation) for heat pump unit
and Tamb. for cooling only unit.
4. If there's I feel function, T compensation is 0. Others are same as above.
(5)Fan mode
Under this mode, indoor fan operates at set fan speed. Compressor, outdoor fan, 4-way valve and electric heating tube stop operation.
Indoor fan can select to operate at high, medium, low or auto fan speed. Temperature setting range is 60.8~86.0
O
F.
2. Other control
(1) Buzzer
Upon energization or command from the unit or remote controller, the buzzer will give out a beep.
(2) Auto button
If press this auto button when turning off the unit, the complete unit will operate at auto mode. Indoor fan operates at auto fan speed
and swing function is turned on. Press this auto button at ON status to turn off the unit.
(3) Auto fan
Heating mode: During auto heating mode or normal heating ode, auto fan speed will adjust the fan speed automatically according to
ambient temperature and set temperature.
(4) Sleep
After setting sleep function for a period of time, system will adjust set temperature automatically.
(5) Timer function:
General timer and clock timer functions are compatible by equipping remote controller with different functions.
(6) Memory function
Memorized compensation temperature, off-peak energization value.
Memory content: mode, up&down swing, light, set temperature, set fan speed, general timer (clock timer can't be memorized).
After power recovery, the unit will be turned on automatically according to memory content.
(7) Health function
Turn on the unit by pressing auto button, and the health is defaulted ON.
Summary of Contents for FSHW091
