background image

21

Suggestions for convect broil:

1. Be sure to carefully follow all the recommended broil

pan and insert instructions and the directions for

placing the oven racks as provided in the “Broil”

section in this Use & Care Guide.

2. Since 

convect broil 

cooks food faster, reduce the

cook time by 25% from the recommended cook time

of your recipe (check the food at this time). If

necessary, increase cook time until the desired

doneness is obtained.

3.

Close the oven door

 when using convect broil.

Convect broil 

(some models*)

Use the convect broil feature to cook thicker cuts of meats

that require direct exposure to radiant heat and the

convection fan for optimum browing results.

1. Press 

convect  

key 3 times*.

 3 times

2. Press 

start 

(See Fig. 1).

To set convect broil* (convection broil) with a

default oven set temperature of 550°F:

Step

Press

Setting convect 

(convection)

 convert

The convect convert feature allows you to convert any

baking recipe using the convect (convection) feature. The

control uses the normal recipe settings and adjusts to a

lower temperature for convection baking.

Convect convert can only be used with the convect bake

feature.

To set convect using default oven set temperature

of 350°F and adding the convect convert:

Step

Press

1. Press 

convect.

2. Press 

convect convert.

* Some models are not equipped with the Convect broil

feature. When using the convect key to toggle between

the convect features models without the convection broil

feature will only show the Convect Bake and Convect

Roast option settings in the display.

NOTE

NOTE

NOTES

When convect convert is used with a cook time or a

delay start setting, the convect convert feature will

display a "

CF

" for 

check food 

when the bake time is

75% complete (See Fig. 2). At this time the oven control

will sound 1 long beep at regular intervals until the set

cook time has finished.

The convection fan will  begin rotating

 once

convection bake or convection roast has been activated.

When using convect convert cook time reductions may

vary depending on the oven set  temperature.

The minimum amount of cook time allowed using the

convect convert feature with a 

bake time

 or a 

delay time

bake

  setting is 20 minutes.

Layer cakes will have better results using the normal

bake

 feature.

Fig. 1

Fig. 2

SETTING OVEN CONTROLS

The convection fan will  begin rotating

 once

convection broil has been activated (some models).

Summary of Contents for CGEF3055KFA





































Reviews: