background image

INSTALLATION INSTRUCTIONS

30" ELECTRIC SLIDE-IN RANGE

P/N 318201632 (1602) Rev.B

English – pages 1-13

Spanish - pages 14-26

Français – pages 27-40

Printed in United States

Table of Contents

Important Safety Instructions .......................................... 2
Product & Cabinet Dimensions.................................... 3-4
To Avoid Breakage .......................................................... 5
Serial Plate Location....................................................... 6
Factory Connected Power Supply Cord ......................... 6
Power Supply Cord Kit ................................................... 6
Access to Terminal Block & Grounding Strap ................. 6

Electrical Connection to the Range ............................. 7-8
Cabinet Construction ................................................... 8-9
Range Installation ...................................................... 9-10
Leveling the range ........................................................ 10
Check Operation............................................................11
Anti-Tip Brackets Installation ................................... 12-13

Important Notes to the Installer

1.  Read all instructions contained in these installation 

instructions before installing range.

2.  Remove all packing material from the oven and 

the drawer compartments before connecting the 
electrical supply to the range.

3.  Observe all governing codes and ordinances.
4.  Be sure to leave these instructions with the 

consumer.

Important Note to the Consumer

Keep these instructions with your owner's guide for 
future reference.

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED 

INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

 FOR YOUR SAFETY: Do not store or 

use gasoline or other flammable vapors and liquids 

in the vicinity of this or any other appliance.

Canada

United States

Summary of Contents for CGES3065PW














Reviews: