background image

I n s t a l l a t i o n
I n s t r u c t i o n s

B u i l t - I n
Dishwasher

If you have questions,

 call 800-944-9400(US), 800-245-8352 (Canada) or visit our website at:

www.Frigidaire.com

IMPORTANT

 –

 

The dishwasher

MUST be installed to allow for future removal from
the enclosure if service is required.

If you received a damaged dishwasher, you
should immediately contact your dealer or builder.

Optional Accessories – See the Owner’s Manual
for available custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS
shown throughout these instructions. While
performing installations described in this booklet,
gloves, safety glasses or goggles should be
worn.

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

IMPORTANT

 –

 

Observe all

governing codes and ordinances.

Note to Installer

 – Be sure to leave these

instructions for the consumer's and local
inspector's use.

Note to Consumer

 – Keep these instructions

with your Owner’s Manual for future reference.

Skill Level

 – Installation of this dishwasher

requires basic mechanical and electrical skills.
Proper installation is the responsibility of the
installer. Product failure due to improper
installation is not covered under the
ELECTROLUX Appliance Warranty.

Completion Time

 – 1 to 3 Hours. New

installations require more time than replacement
installations.

WARNING

To reduce the risk of electrical shock, fire,
or injury to persons, the installer must
ensure that the dishwasher is completely
enclosed at the time of installation.

READ CAREFULLY.
KEEP THESE INSTRUCTIONS.

Summary of Contents for FFBD1821MW













Reviews: