Specifications
subject to change.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-800-FRIGIDAIRE
•
frigidaire.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
frigidaire.ca
FGFU19F6QF
18.6 Cu. Ft.
All Freezer
FGFU19F6Q 09/14
© 2014 Electrolux Home Products, Inc.
All Freezer (18.6 Cu. Ft.)
with ice maker
Professional
Louvered Grille
(for 79" opening)
(Single Trim Kit shown.)
B
C
A
Cut off
4" for 75"
opening
Top Trim Piece
(for 75" opening)
Trim Kit
E
D
4"
Reversible Kickplate
Leveling System
(2) per unit raises height 2-9/16" min.
Only available with trim kits.
*Minimum depth from face of cabinet side panels
and requires recessed electrical outlet.
Built-In Installation
(without Trim Kit)
Single Unit
(A) 72" (B) 33" (C) 25
1
/
4
" min.*
Double Unit (Side-by-Side)
(A) 72" (B) 66" (C) 25
1
/
4
" min.*
Built-In Installation
(with Trim Kit & Leveling System)
Single Unit
(A) 75" or 79" (B) 33" (C) 25
1
/
4
" min.*
Double Unit (Side-by-Side)
(A) 75" or 79" (B) 66" (C) 25
1
/
4
" min.*
All-Freezer
Cutout
Dimensions
Optional Trim Kits
& Dimensions
Kits include top and side trim
pieces, louvered grille, reversible
kickplate and leveling system
to fit 75" or 79" opening height.
Single Louvered Trim Kit
PN # TRIMKITEZ1
(D) 75
1
/
8
" or 79
1
/
8
" (E) 34
3
/
4
"
Double Louvered Trim Kit
PN # TRIMKITEZ2
(Includes hardware to secure
side-by-side units together.)
(D) 75
1
/
8
" or 79
1
/
8
" (E) 67
1
/
8
"
Note: Both kits attach
directly to cabinetry through
top trim piece or louvered
grille to stabilize unit(s).
Refer to detailed kit installation
instructions packed with
kit or on web.
Allow at
least 57
1
/
4
" with door in
90
°
open position
71
3
/
8
"
24
1
/
4
"
29" to handle
extension
Power
cord
location
(right
bottom
rear)
70
5
/
8
"
26
1
/
2
"
32"
Water inlet location (left bottom rear)
and ice maker connection
location (left top rear)
Recessed electrical outlet
25"
Countertop
24"
Cabinet
25
1
/
4
" min. side panels,
1
/
2
" min. width
(Trim Kit installation requires
3
/
4
" min. width)
Recessed water line
•
Freezer must be placed on level surface of hard material, same height
as flooring. Surface must support approximately 800 lbs. when fully
loaded. Unit equipped with 4-point leveling.
“Built-In Look” Specifications
•
Minimum opening of 72" H x 33" W x 25-1/4" D required for single-
unit “Built-In Look” installation; 66" W required for double-unit
installation. (72" H to be measured from finished floor to underside
of soffit or overhead cabinet.)
•
Remove all wall / floor molding prior to built-in installation.
Optional Trim Kit Specifications
•
If optional Single or Double Louvered Trim Kit is to be used, different
cutout dimensions are required. Kit can be adapted to fit either 75"
or 79" opening height.
(Refer to cutout dimensions on this page and
detailed Louvered Trim Kit installation instructions included with kit or
on web.)
•
Remove all wall / floor molding prior to built-in installation.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at frigidaire.com for detailed instructions.
Optional Accessories
•
Single Louvered Trim Kit – (PN # TRIMKITEZ1).
•
Double Louvered Trim Kit – (PN # TRIMKITEZ2).
Built-In All-Freezer Specifications
•
Product Shipping Weight – 255 Lbs.
•
An electrical supply with grounded three-prong receptacle is required.
The power supply circuit must be installed in accordance with current
edition of National Electrical Code
(NFPA 70)
and local codes &
ordinances.
•
Voltage Rating – 115V / 60 Hz / 20 Amps
•
Connected Load (kW Rating) @ 115 Volts = 0.55 kW
•
Amps @ 115 Volts = 5 Amps
•
Always consult local and national electric & plumbing codes.
•
Water line for ice maker can enter opening through floor or rear wall
Copper tubing recommended between cold water line and water
connection location. Water line tubing recommended is 48" minimum
length by 1/4" diameter. Installation of easily accessible shutoff valve in
water line required.
•
Minimum 25-1/4" depth requires recessed electrical outlet and copper
water line.
•
To allow for ease of installation, tape excess power cord to back of unit.
•
To allow for ease of moving out side-by-side units after installation, 84"
minimum length of coiled copper tubing recommended.
•
When installing freezer adjacent to wall, cabinet or other appliance
that extends beyond front edge of unit, 20" minimum clearance
recommended to allow for optimum 140° door swing, providing
complete drawer / crisper access and removal.
(Absolute 4" minimum
clearance will ONLY allow for 90° door swing which will provide limited
drawer / crisper access with restricted removal.)
