Frigidaire Gallery FGGF3054M Use And Care Manual Download

Page: 37 / 40

Solutions to common problems

•

BEFORE YOU CALL

Oven portion of

appliance does not

operate. Gas

cooktop burners

operate.

Problem

Possible Causes

Solutions

Be sure the oven control was set correctly for the requested

feature. See

Setting Oven Controls

section and review

instructions for the desired cooking function in this manual or

see "Entire appliance does not operate" in this checklist.

Be sure gas regulator valve is set to the ON position. See

installation instructions.

Gas regulator shut-off valve

may have been moved to OFF

at installation.

Entire appliance

does not operate.

Be sure appliance power cord is plugged properly to electrical

outlet. Check house circuit breaker; reset if needed. If the

electric service to the house is out, call your local electric utility

for service.

Incorrect oven control

setting.

Power supply to appliance

disconnected or electrical

power outage.

Contact your dealer, installing agent or authorized service agent

for assistance.

Service wiring is incomplete.

Cannot move

appliance easily.

Appliance must be

accessible for

service.

Range is not level.

To correct, place oven rack in center of oven. Place a bubble

level centered on the oven rack. Adjust by turning leveling legs

at bottom of range until the oven rack rests level.

Convect fan does not

start immeadiately or

turns ON and OFF

while cooking (some

models).

The convect fan will turn OFF if the oven door is opened while

any convect feature is active. Close oven door.

Convect fan turns on

with features that

should run without a

fan (some models).

For some models the convect

fan may turn ON while

preheating.

Oven control displays

Prob ERR

". The

probe is not

recognized by the

oven control.

If the error code persists, the

probe may be damaged or

the probe cable has a short.

Floor is not level, weak or

unstable.

If floor under range is sagging or sloping, contact a carpenter to

correct the problem.

The cooktop or oven racks

are not level.

Be sure kitchen cabinets are square & have sufficient room for

appliance clearance.

Cabinet alignment may make

range appear not level.

Contact builder or installer to make appliance accessible.

Gas line is hard-plumbed.

Replace gas supply line with a flexible

CSA International

approved metal appliance connector.

Carpet interferes with range.

Provide sufficient space so appliance may be lifted over carpet.

Cabinets are built in too

tightly to appliance sides.

The convect fan start time is

delayed.

This is normal. The convect fan

will take 6 minutes to begin

rotating

after starting any convect feature.

Oven door is open.

This is normal (if equipped).

Convect fan makes

noise (some models).

The convect fan may turn ON

or OFF automatically.

This is normal. On some cooking features the convect fan may

run until the feature is done or the oven door is opened.

The probe is not fully inserted

into the probe receptacle.

Double check that the temp probe is fully inserted into probe

receptacle. Use only the probe originally supplied with range.

Remove the

probe

from receptacle and oven. The oven may

still be used normally without the probe. Call your authorized

service agent for a replacement probe.

Summary of Contents for Gallery FGGF3054M









































Search results

Summary of Contents for Gallery FGGF3054M

Reviews:

Related manuals for Gallery FGGF3054M

Brands by name

Popular brands

Frigidaire Gallery FGGF3054M, Use And Care Manual

Search results

Summary of Contents for Gallery FGGF3054M

Reviews:

Related manuals for Gallery FGGF3054M

Brands by name

Popular brands