background image

 

                                                                                                                               

 

ENG 

 

 

 

UNPLUG THE COOLER PRIOR TO ANY MAINTENANCE OR SERVICE 
OPERATIONS. REMOVE THE PLUG AND MAKE SURE THAT THE 
OPERATOR CAN CHECK FROM ANY OF THE POINTS WHICH HE 
HAS ACCESS THAT THE CABLE IS UNPLUGGED.

 

 

After maintenance operations, make sure that the grounding 
connections are in place before assembling the covers. Make sure 
you use the same fastening components and covers.

 

 

If any electrical components need to be replaced, use only the 
identical components in the spare part list supplied by the technical 
service department of Frigoglass. 

 

Keep the glass door of the cooler closed during cooling mechanism 
maintenance. The appliance will not stand stable when the 
compressor is disassembled. If the compressor needs to be 
replaced, use adequate support to stabilize the cooler.

 

 

After maintenance operations make sure that the strain relief, which 
supports the supply cord, is assembled properly.

 

 

If the ICM is not functioning properly or is out of order, please check the following before calling the 
authorized service provider: 
 

FAULT 

POSSIBLE REASONS 

HANDLING 

The ICM does not 
work.

 

Power cord not plugged in. 

Plug it in. 

No power supply at the socket. 

Check the outlet fuse. 

The cooler does not 
cool. 

 

The ICM has recently been reloaded 
with warm products. Please note 
that it takes some time to cool warm 
products. 

Preferably, reload the ICM before night 
closing. 

The ICM is loaded in such a way 
that the air circulation in the interior 
is getting blocked. 

Load the ICM according to the 
standards you have been provided 
with by the company. 

The door does not seal properly. 

Repair the doors for proper closing 
(this type of repair should be 
performed by an authorized 
technician). 

Leakage in the cooling system. 

Repair the leakage (this type of repair 
should be performed by an authorized 
technician). 

 
 
 
 

FAULT 

POSSIBLE REASONS 

HANDLING 

The ICM makes 
noise.

 

Intense metallic noise. 

Call a Service technician. 

Inclined or curved floor. 

Level the ICM properly by adjusting its 
feet. Placing a spirit level on the top of 
the ICM will assist you in leveling it. 

Summary of Contents for Flex 56 B HC














Reviews: