25 - DEUTSCH
7 HINWEISE ZUR FEHLERSUCHE
7.1 ALARMERKENNUNG (FÜR QUALIFIZIERTES PERSONAL)
Die elektronische Karte „OMEGA“ ist eine äußerst wirksame logische Kontrolleinheit, welche in der
Lage ist, eventuelle Unregelmäßigkeiten der Maschine durch auf dem Display erscheinende
alphanumerische Hinweise aufzuzeigen; durch ihre korrekte Auswertung kann der Fachmann die
Ursache einer eventuellen Störung rasch erkennen.
Um die Alarm-Hinweise sichtbar zu machen, muss man die elektronische OMEGA Karte die
Tastatur des Modell VIBE Art D13.096 anschliessen.
HINWEIS
BESCHREIBUNG
ABHILFE
EME
NOTFALL
Die Klappenöffnung ist geöffnet oder die
Ausgabeklappe ist nicht korrekt montiert.
Es ertönt ein wechselndes Beep-Signal.
Klappe schliessen und/oder
Ausgabeklappe montieren
TER
ALARM MOTOR-
WÄRMESCHUTZ
Wenn der Wärmeschutz eines Motors einsetzt, erfolgt
ein Aufleuchten des blinkenden Leds TER und ein
wechselndes Beep-Signal
Nach einer Maschinenkontrolle
zur Wiederinbetriebnahme die
Taste STOP drücken.
elektronische Karte resetieren
Software neu installieren
EPO
ALARM
GESPEICHERTE
DATEN
Beim Anschalten der Maschine kontrolliert der
Mikroprozessor die in EPROM gespeicherten Daten;
sollten darin nicht korrekte Daten enthalten sein,
erscheint auf dem Display die Schrift EPO und es ertönt
ein wechselndes Beep-Signal.
Karte ersetzen
elektr. Karte resetieren
Software neu installieren
EPI
SPEICHER-
ALARM
Sollte der Speicher nicht erkannt werden, erscheint
während des Betriebes auf dem Display die Schrift EPI
und es ertönt ein wechselndes Beep-Signal.
Karte ersetzen
LI
ALARM
SPANNUNGS-
VERSORGUNG
Sollte während des Betriebes die Spannung zu gering
sein, erscheint auf dem Display die Schrift LI und es
tönt ein wechselndes Beep-Signal.
Die Netzspannung und die
Spannungsversorgung der
Maschine prüfen.
FLAT Verbindung kontrollieren
elektronische Karte resetieren
Out-Karte ersetzen
OUT
ALARM
AUSGANGS-
MODUL
Sollte während des Betriebes das Steuermodul der
Ausgänge defekt sein oder nicht erkannt werden,
erscheint auf dem Display die Schrift OUT und es ertönt
ein wechselndes Beep-Signal.
Haupt-Karte ersetzen
TA-Verkablung kontrollieren
TA
ALARM TA
Sollte während des Betriebes eine Unregelmäßigkeit
am Amperemetertransformator auftreten, erscheint auf
dem Display die Schrift TA und es ertönt ein
wechselndes Beep-Signal.
TA ersetzen
elektronische Karte resetieren
Software neu installieren
UTA
ALARM MIKRO TA
Sollte während des Betriebes eine Unregelmäßigkeit
am Mikroprozessor auftreten, erscheint auf dem Display
die Schrift UTA und es ertönt ein wechselndes Beep-
Signal.
Micro-TA ersetzen
Summary of Contents for VIBE-GEL 05 Series
