Frigor FBC-601 Instruction Manual Download | Manualshive

Page: 15 / 16

background image

SHUT DOWN

Remove the merchandise from the display compartment and transfer to another storing place

Unplug power plug or switch off control switch

If the cabinet is to be shut down for any length of time, clean cabinet

When stored in a storage room, cover with a cotton sheet.

Do not use plastic tarpaulins as these may encourage formation of moisture and odours
inside the cabine

In the interest of continual product development we reserve the right to change any of the

details and specifications without notice.

Page 15

«
...
13
14
15
16
»

Summary of Contents for FBC-601

















Reviews:

No comments

Related manuals for FBC-601

Brand: Waeco Pages: 80

Brand: Gaggenau Pages: 68

Brand: Hanseatic Pages: 64

Brand: KoolMore Pages: 5

MARLEY AV 98-1514E

Brand: SPX Cooling Technologies Pages: 32

Brand: Siemens Pages: 52

Brand: Siemens Pages: 111

Brand: Siemens Pages: 87

Brand: Siemens Pages: 102

Brand: Aspes Pages: 68

Brand: Schmick Pages: 9

Brand: SCAN domestic Pages: 10

Brand: Signature Kitchen Suite Pages: 45

Brand: KRAFT Pages: 44

Brand: HAEGER Pages: 44

Freezer PLUS Series

Brand: Lab Research Products Pages: 15

Brand: Diamond Pages: 8

Brand: VALERA Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands