background image

|  

2

                            

User Instructions Low Temperature Freezers Model GLE

Livøvej 22 - 8800 Viborg - Tlf. 86 61 34 11 - www.frigor.dk

User Instructions  Low Temperature Freezers Model UNI/LT

2

USER INSTRUCTIONS

Congratulations on your new low temperature 
freezer. We trust that it will serve you for many years 
to come. In order to gain optimum benefit from 
your freezer, please read the following instructions 
thoroughly and act accordingly. The low-tempera-
ture freezers are used for freezing and long-term 
storing of food products, medical preparations ( 
vaccines, blood plasm, ect.) and other biological 
products.

1. Environmental protection and disposal.

The packaging is designed to protect the 
appliance and its components during 
transportation, and it is made of recyclable 
materials.
 

• Please return the packaging to an

 

   official collection point for recycling.

 

• Old appliances contain reusable

 

    materials and should not be disposed

 

   of together with household refuse.

 

• Remove the spring-action hinges from

 

   the appliance, in order to prevent

 

   children from being entrapped in the

 

   appliance.

 

• Ensure that no part of the refrigeration

 

   tubing is damaged as the refrigerant

 

   in the appliance risks escaping to the

 

   environment.

 

• Information about refrigerant type  

 

 

   and amount will be found on the type

 

   plate on the rear of the appliance

 

   (Fig. 1).

2. Safety instructions.

 

• In order to prevent injuries and or

 

   damage to the appliance, it should

 

   be unpacked and set up by min. two

 

   people.

 

• If upon unpacking the appliance is

 

   found damaged, do not connect to

 

   the mains, but contact the supplier.

 

• 

Interference with or repair to the

 

   appliance should only be carried out

 

   by authorized personnel, in order to

 

   avoid any injuries. (contact the sup-

 

   plier for further information).

 

• Never put naked flames or other igni-

 

   tion sources inside the appliance.

 

• Never touch the freezers interior or

 

   products in the freezer when the  

 

 

   freezer is operating. Use gloves or alike

 

   in order to avoid injuries (frost-bite).

 
 

• Keep the key to the appliance away

 

   from the appliance and out of the

 

   reach of children.

3. Connection to the mains.

 

• For safety reasons the appliance must

 

   be earthed. If you are in any doubt,

 

   please contact an authorized electri 

 

   cian.

 

• The appliance should be left for 5

 

   hours before it is connected to the

 

   mains. If the appliance is connected

 

   before that, there is a risk of damaging

 

   the compressor.

 

• If for any reason the appliance is

 

   disconnected from the mains, please

 

   wait 10 minutes before re-connecting.

 

   The electronic starting device needs

 

   this time to cool down, before a safe

 

   re-start can be made.

4. Before use.

 

• Before use, the interior of the appli-

 

   ance should be cleaned with a mild

 

   soap solution, and wiped off with a dry

 

   clean cloth. Never use any kind of

 

   solvent or other chemicals.

5. Setting up the freezer.

The freezer should not be placed where it 
might be splashed with water, in extreme 
high humidity or in direct sunlight. Any of 
these factors may lead to a reduction in 
performance and shorten the life span of 
the components. The freezer should be 
placed on a horizontal level, and should
not be placed close to a heating appliance 
or heating tubes. Allow a minimum of 50mm 
(2”) clearance on the side and the back. 
The side with the ventilation grill should have 
a clearance of at least 100 mm (4”) in order 
to allow the heat from the compressor
motor to dissipate. Underneath the appli-
ance there should be a gap of 15 mm ap-
prox. (1⁄2”). On a soft surface, e.g. carpet, 
it may be necessary to ensure the correct 
distance by means of spacers.

GB

Summary of Contents for GLE















Reviews: