background image

Safety Rules 4

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Safety is a primary concern in the design and 

manufacture of our products. Unfortunately, our 

efforts to provide safe equipment can be wiped 

out by an operator’s single careless act.
In  addition  to  the  design  and  configuration  of 

equipment, hazard control and accident preven-

tion  are  dependent  upon  the  awareness,  con-

cern, judgement, and proper training of person-

nel involved in the operation, transport, mainte-

nance and storage of equipment.
It has been said “The best safety device is an 

informed,  careful  operator.”We  ask  you  to  be 

that kind of operator.

TRAINING

•  Safety  instructions  are  important!  Read  all 

attachment and power unit manuals; follow all 

safety  rules  and  safety  decal  information. 

(Replacement manuals are available from sell-

ing  dealer.)  Failure  to  follow  instructions  or 

safety  rules  can  result  in  serious  injury  or 

death.

• If you do not understand any part of this man

-

ual and need assistance, see your dealer.

• Operators must be instructed in and be capa

-

ble of the safe operation of the equipment, its 

attachments, and all controls. Do not allow any-

one  to  operate  this  equipment  without  proper 

instructions.

• Never allow children or untrained persons to 

operate equipment.

• Train all new personnel and review instruction’s 

frequently with existing workers. A person who 

has not read and understood all operating and 

safety instructions is not qualified to operate the 

machine. An untrained operator exposes himself 

and  bystanders  to  possible  serious  injury  or 

death.

PREPARATION

• 

Always wear relatively tight and belted clothing to 

avoid getting caught in moving parts.Wear sturdy, 

rough-soled work shoes and protective equip-

ment for eyes, hair, hands, hearing, and head; 

and  respirator  or  filter  mask  where  appropri-

ate.

•  Make  sure  attachment  is  properly  secured, 

adjusted, and in good operating condition.

• Power unit must be equipped with ROPS or 

ROPS  cab  and  seat  belt.  Keep  seat  belt 

securely  fastened.  Falling  off  power  unit  can 

result in death from being run over or crushed. 

Keep  foldable  ROPS  system  in  “locked  up” 

position at all times.

•  A  minimum  20%  of  tractor  and  equipment 

weight  must  be  on  the  tractor  front  wheels 

when  attachments  are  in  transport  position. 

Without this weight, tractor could tip over, caus-

ing personal injury or death. The weight may be 

attained with a loader, front wheel weights, bal-

last in tires or front tractor weights. Weigh the 

tractor and equipment. Do not estimate.

TRANSPORTATION

• Always  comply  with  all  state  and  local  laws 

governing  highway  safety  and  lighting  and 

marking requirements.

•  Never  allow  riders  on  power  unit  or  attach

-

ment.

• Do not operate or transport on steep slopes.
• Use extreme care and reduce ground speed 

on slopes and rough terrain.

• Do not operate or transport equipment while 

under the influence of alcohol or drugs. Consult 

your doctor about operating this machine while 

taking prescription medications.

OPERATION

• Never go underneath equipment (lowered to 

the  ground  or  raised)  unless  it  is  properly 

blocked and secured. Never place any part of 

the  body  underneath  equipment  or  between 

Summary of Contents for DH1376

























Reviews: