background image

INSTALLATION AND MAINTENANCE MANUAL 

 

TRANSLATION OF THE 
ORIGINAL DOCUMENT 

For additional copies visit: 

www.frost‐trol.com

 

WALEN SOLID 

LINES 

D008586

 Versión: 

-6- 

 

 

Do not expose the equipment to atmospheric agents. 

 

 

Do not store explosive substances such as aerosol cans with a 
flammable propellant in the refrigerated cabinet. 

 

 

Keeping pharmaceuticals, glass bottles or flasks in the cabinet is 
strictly forbidden. 

 

 

Only qualified personnel can remove panels or guards, and specially 
the electric board cover, when this requires the use of tools. 

 

 

Before obtaining access to terminals, all supply circuits must be 

disconnected. 

 

 

Unplug the cabinet before performing any form on internal servicing of 

the unit. 

 

 

The power cords must be properly spread out, safe from shocks and 

far from liquids, water and heat sources, and in perfect condition. The 
use of adaptor plugs is forbidden. 

 

 

If the power cord is damaged, it must be replaced by the 
manufacturer in order to avoid a hazard. 

 

 

Earthing is mandatory according to current legislation, as is providing 

protection against power surges, short circuits and indirect contacts. 

 

 

Ensure that the power supply voltage meets the details on the rating 
plate of the cabinet. The cabinet must be properly connected to the 

earthing system. 

 

 

Do not use direct or indirect water jets on the cabinet. Do not touch 
the equipment with damp or wet hands or feet; do not use it while 

barefoot. 

 

 

Parts that form the refrigeration circuit must not be cut or separated 
until the refrigerant has been removed for recovery at a specialized 

centre. 

 

Summary of Contents for WALEN





























Reviews:

Related manuals for WALEN