background image

3. Insufficient Water Pressure 
4. Blue Plug Still Installed 

2. Disconnect the tube between 
the membrane and pre-filter (like 
the pre-flushing instructions) and 
run water at full pressure to see if 
water comes out of the filter. – If 
the water does not come out (or 
is very weak pressure) the filter 
may need to be changed. 
3. Reverse Osmosis required 
50psi (Minimum) to operate – 
70psi+ is ideal. If you have lower 
than 50psi pressure this unit may 
not be suitable for you. Low 
Pressure Membranes are 
available for an additional charge 
that will work down to 20psi. 
4. Remove the blue plug from the 
drinking water line. 

Water is coming out slowly 

Reverse Osmosis 

RO filtration is a slow process, 
depending on the system you 
have purchased, you will only get 
about 8 – 12L of water per hour. 

I am getting much more waste 
water than filtered water 

1. Water Pressure 
 
 
2. Water Quality 
 
 
3. Blockage 

1. Our units are designed to run 
at approx. 1:1 – 1:1.5 waste 
water ratio at 70 psi. If your 
pressure is lower than 70 psi, the 
production rate may decrease 
and cause more drain water than 
filtered water. 
2. If your inlet water quality is 
poor and contains higher salts 
and hardness the filter may 
produce lest water than the 
specified amount. 
3. If you have good pressure, 
and average water quality it is 
possible there is a small 
blockage somewhere in the 
system. Try to follow the water 
flow along the system, 
disconnecting 1 tube at a time to 
try and pinpoint where the water 
is ‘stopping’ 

High pH Reading 

1. Insufficient Testing Equipment 
 
 
2. Wrong Configuration 

1. pH testing equipment can 
range from a cheap test pen right 
up to lab grade equipment. 
Before coming to a conclusion on 
pH issues, it is best to ensure the 
equipment used to measure the 
pH of the RO water is of high 
standards and suitable for 
reading pH levels in low EC 
water (i.e. The guy at the pool 
shop is not going to cut it). We 
have access to high quality 
testing equipment and frequently 
test our units and conduct 
research. If you feel that there is 
an issue with your pH, please 
contact us. 

Summary of Contents for GT1-70DI











Reviews: