background image

User’s manual · TSQ 310 

 

         

- 16 -                TSQ  310                 version_en_1.1              FTE maximal 

 

Chapter 2.  

Technical features 

 

Ref. TSQ 

310 

Code 

2003532 

Input frequancy margin 

950-2150 MHz 

Input level 

-25 a -65 dBm 

Imput impedance 

75

 

LNB (feeding/conmutation) 

13V-18V / 0-22kHz 

Input connector 

Female F connector 

Input LOOP losses 

<1 dB 

FEC 

1/2, 2/3, 3/4, 5/6, 7/8, 8/9, 9/10, 1/4, 1/3, 

1/5, 2/5, 3/5, 4/5 DVB, RS 204,188 

Input modulation 

8PSK, QPSK 

Input Symbol Rate 

DVB-S:1-45 MS/s / DVB-S2:1-37 MS/s 

Modulation Error Ratio (MER) 

Typ. 40 / Mín. 36 

Selectable format of output modulation 

16 QAM, 32 QAM, 64 QAM, 128 QAM, 256 QAM 

Output symbol Rate 

1-6,96 MS/s 

Roll-Off Factor 

13 %,15% 

Output channels 

C2-C69 

Output connectores 

Female F connector 

Output Level 

80 dBuV 

Regulation margin 

15 dB 

MIX Losses 

<1 dB 

Band spurious 

-60 dBc 

Programming Interface 

RJ-45 

Programmer 

PRO 201, media Max EVO and media Max MINI 

Operating temperature 

0ºC-45ºC 

Consumption 5V (mA) 

800 

Consumption 12V (mA) 

300 

Consumption 24V (mA) 

15 

Consumption 30V (mA) 

Dimensions 

75x265x150 mm 

Weight 

1,4Kg 

 

Chapter 3.  

Declaration of conformity 

 

CONFORMITY DECLARATION 

 

“WE , FTE MAXIMAL, DECLARE THAT THE PRODUCT  

TSQ 310 

IS IN CONFORMITY WITH FOLLOWING DIRECTIVES 

Low Voltage Directive 2006/95/EC 

EMC Directive 2004/108/EC” 

If you wish a copy of the conformity declaration, please contact to the company 

Summary of Contents for TSQ 310

















Reviews: