background image

3

 

2017 Fueltec  Model CF50E Fuel Polishing System 

 

Prevent Explosions and Fires 

 

 

Fuels and their vapors will explode or burn, if ignited. Spilled or leaking fuels and used filters cause vapors.  All used filters 

should be promptly placed in an approved safety container until disposed of.      

 

Even filling air compressor fuel tanks will cause potentially dangerous vapors in the vicinity of the work area. 

 

 

Working Alone

 

 

 It is highly recommended that someone who is capable of rendering first aid be present during operation. Familiarize your-

self with Cardiopulmonary Resuscitation (CPR) methods, while working around fuel vapors. This information is available 

from the American Red Cross. Always advise other personnel about where you will be working, and caution them not to ac-

tivate power tools or engines while you are working with fuel filtration equipment. Use the OSHA Lockout/Tagout proce-

dures. If you are not familiar with this requirement, refer to OSHA documentation.

 

 

Hazardous Materials 

 

 

Some materials may present a health hazard if not handled correctly. Ensure that you clean hands after handling equip-

ment. Do not place any equipment in the mouth. 

 

 

FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS AND SAFETY PRECAUTIONS 

COULD RESULT IN PROPERTY DAMAGE, INJURY OR DEATH. 

 

 

FIRE HAZARD! 

 

 

Do NOT use power tools (Class I Division I and Class I Division II) during the operation or maintenance of equipment. 

Sparking could ignite fuel or vapors, resulting in fire. 

 

 

CHEMICAL EXPOSURE HAZARD! 

 

 

Wear appropriate safety equipment during operation or maintenance of equipment. Avoid exposure to fuel and vapors.        

Prolonged exposure to fuel may cause severe skin irritations and possible burns. 

 

 

REQUIREMENTS FOR USE 

 

 

• 

Fueltec 

fuel polishing and tank cleaning systems are designed for use only by trained personal. Free training is available 

at Fueltec

s factory located in Granite Falls, NC USA. Call 1

-

 (828) 212

-

1141 

 

 

• 

 The operation of 

Fueltec

s

 systems must be consistent with NFPA Code 30A, OSHA regulations, and federal, state and 

local fire codes, and other applicable local regulations. 

 

 

OPERATING PRECAUTIONS 

 

 

• 

NO SMOKING. Extinguish all open flames and pilot lights, such as on RV appliances. 

 

 

• 

TURN OFF cell phones and other electronic devices to prevent sparks which could cause an explosion or fire. 

 

 

PERSONAL SAFETY

 

 

Stay alert, watch what you are doing and use common sense when operating or maintaining the system. Do not operate or 

maintain the system while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention 

while operating or maintaining the system may result in serious personal injury or death.

 

Dress properly while operating this system. Do not expose bare skin or eyes to fuels.  Prolonged contact with fuel can damage 

the skin. Use safety apparel and equipment. Use safety goggles or safety glasses. Also use non

-

skid safety shoes, hardhat, 

gloves, and fall protection when appropriate.

 

Summary of Contents for CF50E



























Reviews: