– 9 –
6-8
Alarm (Ch8)
Sets the detect conditions for each type of alarm.
6-9
Communication (Ch9)
Sets the communication conditions towards the host computer.
6-10
PFB (Ch10)
Changes settings to use valve control.
"
di1
" (di1)
DI-1 function
selection
Sets the
function of
DI-1
0 (No function)
1 (Switchover between STBY ON/OFF)
2 (Switchover between Auto/Manual)
3 (Switchover between Local/Remote)
4 (No function)
5 (No function)
6 (Start AT (standard))
7 (Start AT (low PV))
8 (No function)
9 (No function)
10 (Ramp SV ON/OFF)
11 (Ramp SV HOLD)
12 (Ramp soak OFF)
13 (Ramp soak RUN/HOLD)
14 (No function)
15 (Latch release (all))
16 (Latch release (DO1))
17 (Latch release (DO2))
18 (Latch release (DO3))
19 (Latch release (DO4))
20 (Latch release (DO5))
21 (Start timer (DO1))
22 (Start timer (DO2))
23 (Start timer (DO3))
24 (Start timer (DO4))
25 (Start timer (DO5))
26 (SV No. + 1)
27 (SV No. + 2)
28 (SV No. + 4)
29 (PID No. + 1)
30 (PID No. + 2)
31 (PID No. + 4)
32 (No function)
33 (No function)
34 (No function)
35 (SV No.+1, PID No.+1)
36 (SV No.+2, PID No.+2)
37 (SV No.+4, PID No.+4)
38 (Pattern No.+1)
39 (Pattern No.+2)
40 (Pattern No.+4)
41 (Soft start)
42 (Ramp soak RUN)
43 (Ramp soak HOLD)
44
(Ramp soak RUN at DO1 startup)
45
(Ramp soak RUN at DO2 startup)
46
(Ramp soak RUN at DO3 startup)
47
(Ramp soak RUN at DO4 startup)
48
(Ramp soak RUN at DO5 startup)
0
(Note11)
"
di5
" (di5)
DI-5 function
selection
Sets the
function of
DI-5
0 to 48
0
"
do1t
" (do1T)
Sets the DO1
output event
type
Sets the
function of
DO1
0 to 102
0
"
doP1
" (doP1)
Sets DO1
option function
Assigns the
four types of
option
functions in
bit units
0000 to 1111
0000
(Note3)
"
do5t
" (do5T)
Sets the DO5
output event
type
Sets the
function of
DO5
0 to 102
0
"
doP5
" (doP5)
Sets DO5
option function
Assigns the
four types of
option
functions in
bit units
0000 to 1111
0000
"
rmP
" (rMP)
ramp SV
ON/OFF
Sets the
ramp SV
ON/OFF
oFF (ramp SV OFF)
on (ramp SV ON)
on
"
rmPL
" (rMPL)
Ramp SV-
Decline
Sets the slope
for a falling SV
during ramp
SV operations
0 to 100% FS
0°C
"
rmPh
" (rMPH)
Ramp SV-
Incline
Sets the slope
for a rising SV
during ramp
SV operations
0 to 100% FS
0°C
"
rmPU
" (rMPU)
Ramp SV-
slope units of
time
Sets the unit
of time for the
slope during
ramp SV
operations
hoUr (slope temperature/hour)
Min (slope temperature/min)
hoUr
"
Svt
" (SvT)
Ramp SV - SV
display mode
selection
Displays the
SV during
ramp
operations or
the SV goal
value on the
SV display
rMP (SV during ramp)
TrG (target SV)
rMP
"
[trL
" (CTrL)
Control
methods
Allows you to
select the
control
method.
Pid (PID control)
FUZY (Fuzzy PID control)
SELF (Self-tuning control)
Pid2 (PID2 control)
Pid
Sections
5-1 to
5-8
(Note19)
Parameter
display symbol
Parameter
name
Function
Setting range
Initial
value
Remarks
RST
…
…
…
…
…
bit0 : output latch function
bit1 : error alarm function
bit2 : non-excitation output
alarm function
bit3 : hold reset function
□□□□
RST
…
…
…
…
…
□□□□
bit0 : output latch function
bit1 : error alarm function
bit2 : non-excitation
output alarm function
bit3 : hold reset function
RST
"
PrCS
" (PrCS)
Control target
Allows you to
select the
control target.
SRV1 (Servo control 1)
SRV2 (Servo control 2)
PFB (Position feedback
control)
PFb/
Srv1
(with
PFB/
without
PFB)
(Note16)
"
Stmd
" (STMd)
Start mode
Sets the
operation
mode when
starting up
Auto (auto mode startup)
Man (manual mode startup)
Rem (remote mode startup)
STby (standby make startup)
AUTo
Parameter
display symbol
Parameter name
Function
Setting range
Initial
value
Remarks
"
A1hY
" (A1hy)
ALM1 hysteresis
Sets the hysteresis
for alarm output 1
ON/OFF
0 to 50% FS
1°C
(Note3)
"
dLY1
" (dLY1)
ALM1 delay
Sets the delay
before detecting
alarm output 1
0 to 9999 [sec/min]
0(sec/
min)
"
dL1U
" (dL1U)
ALM1 delay time
units
Sets the delay time
units for alarm
output 1
sec (second)
Min (minute)
sec
"
A5hY
" (A5hy)
ALM5 hysteresis
Sets the hysteresis
for alarm output 3
ON/OFF
0 to 50% FS
1°C
"
dLY5
" (dLY5)
ALM5 delay
Sets the delay
detecting for alarm
output 3
0 to 9999 [sec/min]
0(sec/
min)
"
dL5U
" (dL5U)
ALM5 delay time
units
Sets the delay time
units for alarm
output 3
sec (second)
Min (minute)
sec
"
hb1
" (hb1)
HB alarm set value
for CT
Sets the heater
burnout alarm
detection value for
CT
0.0 to 50.0A
0.0A
(Note10)
(Note13)
"
hb1h
" (hb1h)
HB alarm
hysteresis for CT
Sets the heater
burnout alarm ON/
OFF hysteresis for
CT
0.0 to 50.0A
0,5A
(Note10)
(Note13)
"
hS1
"
Load short-circuit
alarm setting value
for CT
Sets the heater
load short-circuit
alarm setting value
for CT.
0.0 to 50.0A
0.0A
(Note10)
(Note13)
"
hS1h
"
Load short-circuit
alarm hysteresis
for CT
Sets the heater
load short-circuit
alarm ON/OFF
hysteresis for CT.
0.0 to 50.0A
0.5A
(Note10)
(Note13)
"
lbTm
" (LbTM)
Loop break
detection time
Sets the time
before detecting a
broken loop
0 to 9999 sec
0 sec
"
LbAb
" (LbAb)
Loop break
detection range
(°C)
Sets the
temperature range
before detecting a
broken loop
0 to 100% FS
10°C
Parameter
display symbol
Parameter name
Function
Setting range
Initial
value
Remarks
"
Stno
" (Stno)
ST No. setting
Sets the station
number.
0 to 255 (0:
unresponsive
communication)
1
(Note17)
"
CoM
" (CoM)
baud rate/parity
setting
Sets the baud
rate and parity
check
96od (9600 bps/odd)
96Ev (9600 bps/even)
96no (9600 bps/none)
19od (19200 bps/odd)
19Ev (19200 bps/even)
19no (19200 bps/none)
96od
(Note17)
"
S[[
" (SCC)
Communication
permissions
Sets whether or
not overwriting is
possible from the
master side (PC,
etc.)
r (read only permission)
rW (read and overwrite
permission)
rW
(Note17)
Parameter
display symbol
Parameter name
Function
Setting range
Initial
value
Remarks
"
PGAP
" (PGAP)
PFB dead band
Sets the PFB dead
band
0.0 to 100.0%
5%
(Note16)
"
trvL
" (TrvL)
Valve stroke time
Sets the full stroke
time for the valve
5 to 180 sec
30 sec
(Note16)
"
[AL
" (CAL)
PFB input
adjustment
command
Adjusts the zero/
span for PFB input
0 (none/forcibly termination)
1 (zero adjustment)
2 (span adjustment)
3 (automatic adjustment)
-
(Note8)
Parameter
display symbol
Parameter
name
Function
Setting range
Initial
value
Remarks
RST
…
…
…
…
…
RST
