background image

                     

CONTENTS

Contents . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Precautions . . . . . . . . . . . . . . 2 - 4
Getting Started. . . . . . . . . . . . . . . . . . . . . 5
Spray pattern . . . . . . . . . . . . . . . . . . . . . . 6
Distance & Pressure Tube. . . . . . . . . . . . . 7
Spraying techniques . . . . . . . . . . . . . . . . 8
Aircap selection . . . . . . . . . . . . . . . . . . . 9
Latex & Viscosity  . . . . . . . . . . . . . . . 10 - 11
Viscosity guide . . . . . . . . . . . . . . . . . . . .11
Cleaning . . . . . . . . . . . . . . . . . . . . . . .11 - 12
Finish Problems . . . . . . . . . . . . . . . . . . 13
Spray Gun Problems . . . . . . . . . . . . . 14 -15
Needle Packing & Seals. . . . . . . . . . . . 16
Pressure Pot use . . . . . . . . . . . . . . . . . .17
Turbine Care and Maintenance . . . . . . . .18
Parts diagrams. .  . . . . . . . . . . . . . . . . 19 - 21
Spray Gun Holder . . . . . . . . . . . . . . . . . . 22
Service information. . . . . . . . . . . . . . . . 23
Warranty information . . . . . . . . . . . . . .  24
CE Declaration  . . . . . . . . . . . Back Cover

24

Fuji Industrial Spray Equipment Ltd. (“Fuji”) provides a 24 month limited
warranty on the product to the original purchaser effective from the date
of purchase against defects in materials and workmanship.

The warranty does not cover damage or defects arising as a result of
abuse, misuse, accident, negligence, malfunction, corrosion, normal
wear and tear, inadequate or lack of spray gun or other aspects of
maintenance of the product, damage arising from improper assembly,
installation or operation, or damage arising from the product being
used for a purpose other than that for which it was designed or
intended.  The warranty is void if repairs to the product are made or
attempted by anyone other than Fuji or its authorized agent, or if any
modifications to the product are made or attempted.

Purchasers located in North America must obtain a Return Material
Authorization number by calling Fuji at 1-800-650-0930 before
returning the product to Fuji or its designated representative.
Purchasers located outside North America must contact the vendor
from which they purchased the product.  In all instances purchasers
must return the product together with proof of purchase and with
shipping prepaid.  For valid warranty claims the product will be
returned to the purchaser with shipping prepaid.

This is the only warranty provided by Fuji with respect to the
product and is in lieu of any other warranties, express or
implied, including but not limited to any warranty of
merchantability or fitness for a particular purpose.  Fuji’s sole
obligation under this warranty shall, at its option, be to either
repair or replace a product determined by Fuji to be defective.
In no event shall Fuji be liable for loss or profits, incidental or
consequential damages, injury to any person or property, or
any other damages of whatsoever nature.

 

Fuji Limited 2 Year Warranty

Summary of Contents for XPC Series

























Reviews: