Fuji Xerox ApeosPort-V 4070 Administrator'S Manual Download

Page: 375 / 719

Configuration of Encryption using IPsec

375

an
d

Di
gi

l S
ign
at

ure

Important •

You cannot import a certificate that has been already registered in [Local Device] or [Others]. Delete
the registered certificate before importing.

•

If the certificate to be imported contains the V3 extension "keyUsage", "digitalSignature" must be
asserted.

1) Click the [Properties] tab.

2) Click [Security] to display the items in the folder.

3) Click [Machine Digital Certificate Management].

4) Click [Upload Signed Certificate].

5) Enter [Password].

6) Enter [Retype Password].

7) Enter a file name you want to import or select a file to import from a dialog box

displayed by clicking the [Browse] button, and then select [Save].

8) Click the [Import] button.

9) Refresh the web browser.

Configure the certificate.

1) Click [Security].

2) Click [Certificate Management].

3) Select [Local Device] for [Category] and [IPsec] for [Certificate Purpose], and then click

the [Display the list] button.

4) Select the check box next to the certificate to set.

5) Click the [Certificate Details] button.

6) Click the [Use this certificate] button.

7) Click [Reboot Machine]. The machine reboots and the settings are enabled.

Step2 Configuration on the Machine (Configuration of IPsec)

The following describes configuration procedures to set up IPsec on the machine.

Press the <Log In/Out> button.

Enter the system administrator's user ID with the numeric keypad or the keyboard
displayed on the screen, and select [Enter].

When a passcode is required, select [Next] and enter the system administrator's passcode,
and select [Enter].

Note

•

The default user ID is "11111".

•

The default passcode is "x-admin".

Select [Tools] on the Services Home screen.

Select [Connectivity & Network Setup].

Select [Security Settings].

Select [IPsec Settings].

Configure the required settings.

For details on the settings, refer to "IPsec Settings" (P.201).

Select [Close].

Summary of Contents for ApeosPort-V 4070















































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ApeosPort-V 4070

Reviews:

Related manuals for ApeosPort-V 4070

Brands by name

Popular brands

Fuji Xerox ApeosPort-V 4070, Administrator'S Manual

Search results

Summary of Contents for ApeosPort-V 4070

Reviews:

Related manuals for ApeosPort-V 4070

Brands by name

Popular brands