manualshive.com logo in svg

Fuji Xerox ApeosPort-V 4070, Administrator'S Manual

The Fuji Xerox ApeosPort-V 4070 is a versatile multifunction printer designed for office use. To optimize its features, the Administrator's Manual is a comprehensive guide that can be downloaded for free from our website, providing step-by-step instructions and configuration options to enhance productivity and efficiency.

Share
Download
background image

HP-GL/2 Emulation

649

A

p

pe
ndi
x

16

2) Because there are no font size specification commands and all pen widths are 0.1 mm in 

the above example, add the height/2 of the default font size for A3 size paper (75 
plotter units) to the active coordinates area obtained in step 1.

The active coordinates area obtained in step 2 is -8474,-6013,8474,6013.

3) The value set in paper margins (10 mm = 400 plotter units) is subtracted from the active 

coordinates area obtained in step 2.

The active coordinates area obtained in step 3 is -8074,-5613,8074,5613.

4) As the active coordinates area obtained in step 3 exceeds the A4 size and is A3 size, the 

document size is determined to be A3.

In addition, when the paper margin setting is 0 mm and the active coordinates area is -
8474,-6013,8474,6013, and this exceeds A3, but is A2 or smaller, the document size is 
determined to be A2.

How to Determine Paper Size

If the operation panel settings are as follows, the paper size is determined as below.

Document size: Auto

Paper Tray: Auto

The method for determining the paper size differs according to the paper size and scaling 
mode settings on the operation panel.

„

If the Paper Size Setting is A Sizes

The paper sizes among the three sizes (A3, A4, and A5) that are actually loaded in the trays 
become the possible paper size.

If A series paper (A3, A4, A5) is not loaded in the trays, all three sizes, A3, A4, and A5 become 
possible sizes; a message is displayed on the touch screen prompting the user to load A series 
paper.

„

If the Paper Size Setting is Auto

The paper sizes among the five sizes (A3, B4, A4, B5, and A5) that are actually loaded in the 
trays become the possible paper size.

If A3, B4, A4, B5, or A5 paper is not loaded in the trays, all five sizes become possible sizes; 
a message is displayed on the touch screen prompting the user to load paper.

„

If the Scaling Mode Setting is Paper Size

If the paper size and the document size are the same, select paper that is the same size as 
the document.

If the document size is larger than any possible paper sizes, select the largest paper.

If the document size is smaller than any possible paper sizes, select the smallest paper.

„

If the Scaling Mode Setting is ACA

Select the smallest paper size that can contain the ACA.

If the active coordinates area is larger than any possible paper sizes, select the largest paper.

If the active coordinates area is smaller than any possible paper sizes, select the smallest 
paper.

Note

•

If the document size is set to anything other than Auto, the paper size is the one set on the control 
panel.

•

If the paper tray is set to Auto, the paper size is the one loaded in each tray. However, If paper 
whose size is not supported is loaded, an error message will be displayed prompting the user to load 
a supported paper.

Summary of Contents for ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ApeosPort-V 4070

Canon Pixma MG2400 Series Getting Started Manual preview
Pixma MG2400 Series
Brand: Canon Pages: 2
QMS 4060 Supplementary Manual preview
4060
Brand: QMS Pages: 27
QMS 4060 Accessories Manual preview
4060
Brand: QMS Pages: 3
Primera Bravo SE Quick Start preview
Bravo SE
Brand: Primera Pages: 2
TP UP-PN Operation Manual preview
UP-PN
Brand: TP Pages: 10
Lexmark X748dte Product Specification preview
X748dte
Brand: Lexmark Pages: 2
Oki ES5460 User Manual preview
ES5460
Brand: Oki Pages: 128
Oki B2540 Brochure & Specs preview
B2540
Brand: Oki Pages: 2
idp SMART-21S User Manual preview
SMART-21S
Brand: idp Pages: 63
Oki MPS6500b User Manual preview
MPS6500b
Brand: Oki Pages: 132
Tektronix Phaser 220 Reference Manual preview
Phaser 220
Brand: Tektronix Pages: 178
MIMAKI UJF-605R II Daily Care Manual preview
UJF-605R II
Brand: MIMAKI Pages: 28
BIXOLON SPP-R220 Installation Manual preview
SPP-R220
Brand: BIXOLON Pages: 20
Go ET-15000 SP Setup preview
ET-15000 SP
Brand: Go Pages: 3
imagistics DL155 User Manual preview
DL155
Brand: imagistics Pages: 2
Xerox CopyCentre 118 Installation Manual preview
CopyCentre 118
Brand: Xerox Pages: 2
Galileo ADP 3000 Quick Reference preview
ADP 3000
Brand: Galileo Pages: 15
Ricoh IM C6500 Operating Instructions Manual preview
IM C6500
Brand: Ricoh Pages: 24

Brands by name

Popular brands

Load more brands