manualshive.com logo in svg

Fuji Xerox ApeosPort-V 4070, Administrator'S Manual

The Fuji Xerox ApeosPort-V 4070 is a versatile multifunction printer designed for office use. To optimize its features, the Administrator's Manual is a comprehensive guide that can be downloaded for free from our website, providing step-by-step instructions and configuration options to enhance productivity and efficiency.

Share
Download
background image

Notes and Restrictions

673

A

p

pe
ndi
x

16

z

When you use Internet Explorer, even if you click "To delete file, click here." in the 
[Document Acquisition] screen of the Store & Send Link service, file deletion may not be 
performed. In this case, use another browser than Internet Explorer to delete the file.

„

Split Files

You cannot select [Single File for Each Page] when using the Store to Folder or Job Flow 
feature.

„

Thumbnail View

Files in a folder may not be displayed in thumbnail view in the following cases. In those 
cases, display them in list view.

- Some file is not displayed in thumbnail view even though it is stored in the folder.
- Characters and images are not correctly displayed because they are scaled down from 

the actual sizes.

z

The orientation of an image displayed in thumbnail view depends on which orientation 
the document was stored in.

z

If the power is cut off immediately after a scanned file is stored in a folder, or if the hard 
disk space is insufficient to display thumbnails, files in the folder may not be displayed in 
thumbnail view. In that case, display them in list view.

„

2 Sided Simultaneous Scan

When [Color Scanning] is set to [Color] and [Color Space] is set to [Device Color Space], 2 
sided simultaneous scan is not available.

„

FTP Transmission for Scan to PC

z

By factory default, [Passive Mode] is selected as a transfer mode to send scanned data 
via FTP from the machine.

z

You can switch the FTP transfer mode using CentreWare Internet Services, but cannot 
switch the mode per job or per destination FTP server.

z

Depending on your network environment, operations may not be performed properly 
unless the FTP transfer mode is switched from [Passive Mode] to [Active Mode].

z

When [IP Filtering] is enabled, make sure to switch the FTP transfer mode to [Active 
Mode].

In [Passive Mode], the server permits a client to connect to the port for the data transfer 
so that the client starts the connection. [Passive Mode] is commonly used and also has 
lower security risk than [Active Mode].

In [Active Mode], a client notifies the server of the port number for the data transfer so 
that the server starts the connection. [Active Mode] may incur a security risk such as 
impersonation by third parties. In addition, the proper connection may not be available 
in a firewall environment. In such a case, select [Passive Mode].

„

SMB Transfer for Scan to PC

z

If you use Mac OS X 10.7 Lion, OS X 10.8 Mountain Lion, or OS X 10.9 Mavericks, contact 
our Customer Support Center and ask if your operating system is supported.

„

Store to WSD

Note

•

WSD stands for Web Services on Devices.

z

When the WSD scan port is not activated, the [Store to WSD] button is not displayed in 
the Services Home screen. Enable the WSD scan port to use the Store to WSD feature on 
the machine.

Summary of Contents for ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ApeosPort-V 4070

Saxxot CRU-158 Operation Manual preview
CRU-158
Brand: Saxxot Pages: 13
Canon S 200 User Manual preview
S 200
Brand: Canon Pages: 198
Oce sx1481 User Manual preview
sx1481
Brand: Oce Pages: 192
Oce OP20 Operation Manual preview
OP20
Brand: Oce Pages: 22
Oce FX3000 SERIES Quick Setup Manual preview
FX3000 SERIES
Brand: Oce Pages: 41
Oce fx2081 Installation Manual preview
fx2081
Brand: Oce Pages: 28
Oce im5530 Specifications preview
im5530
Brand: Oce Pages: 6
QMS 2560 Options Installation preview
2560
Brand: QMS Pages: 104
Oce im2330 Printing Manual preview
im2330
Brand: Oce Pages: 386
Oce im2330 Specifications preview
im2330
Brand: Oce Pages: 2
Oce cm2520 Safety Information & Getting Started preview
cm2520
Brand: Oce Pages: 27
Oce im2330 Operator'S Manual preview
im2330
Brand: Oce Pages: 324
Oki OKIPAGE14e Setup Manual preview
OKIPAGE14e
Brand: Oki Pages: 28
Oki OKIPAGE14e Limited Warranty preview
OKIPAGE14e
Brand: Oki Pages: 22
Canon image RUNNER 3045 Manual preview
image RUNNER 3045
Brand: Canon Pages: 14
Oki ES2024 User Manual preview
ES2024
Brand: Oki Pages: 512
Oki B6500n Installation Manual preview
B6500n
Brand: Oki Pages: 1
DataSouth Documax A6300 Series User Manual preview
Documax A6300 Series
Brand: DataSouth Pages: 180

Brands by name

Popular brands

Load more brands