Fuji Xerox ApeosPort-V 4070 Administrator'S Manual Download

Page: 253 / 719

Setup

253

Tools

When you finish required settings, select [Save].

Folder Name

Set the folder name. Enter up to 20 single-byte characters using the keyboard displayed or
the numeric keypad.

For information about how to enter characters, refer to "Entering Text" (P.39).

Check Folder Passcode

Set an access restriction to permit operations for specified users only.

Check Folder Passcode

Set whether or not to set a passcode.

Off

Does not set an access restriction.

Set a passcode for access restriction.

Folder Passcode

To use the Check Folder Passcode feature, enter a passcode. You can enter a passcode of up
to 20 numeric digits (0 to 9).

Target Operation

Set the operations to be restricted.

Always (All Operations)

A passcode entry is required when a folder is selected or a file in a folder is printed or
deleted.

Save (Write)

A passcode entry is required when a folder is selected.

Print/Delete (Read)

A passcode entry is required when printing or deleting the file in the folder.

Delete Files After Retrieval

When a file stored in a folder is printed or is retrieved from a remote server, set whether the
file should be deleted.

The file is left stored.

Yes

After the file is printed, or is retrieved by an external source, it is automatically deleted.

Note

•

If you select [Yes], a file is not deleted when retrieved from CentreWare Internet Services.

Delete Expired Files

Specify whether or not to enable the operation to delete files stored in a folder at a specified
time after a retention period has elapsed.

Even when the retention period has elapsed, files are not deleted.

Summary of Contents for ApeosPort-V 4070















































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ApeosPort-V 4070

Reviews:

Related manuals for ApeosPort-V 4070

Brands by name

Popular brands

Fuji Xerox ApeosPort-V 4070, Administrator'S Manual

Search results

Summary of Contents for ApeosPort-V 4070

Reviews:

Related manuals for ApeosPort-V 4070

Brands by name

Popular brands