manualshive.com logo in svg

Fuji Xerox ApeosPort-V 4070, Administrator'S Manual

The Fuji Xerox ApeosPort-V 4070 is a versatile multifunction printer designed for office use. To optimize its features, the Administrator's Manual is a comprehensive guide that can be downloaded for free from our website, providing step-by-step instructions and configuration options to enhance productivity and efficiency.

Share
Download
background image

7 Printer Environment Settings

312

P

rint
e

r En

v

iro
nmen

t Set

tin

g

s

7

3

Set an IP address and the other addresses.
Skip this step if an IP address is already set.
If DHCP or BOOTP is available in your environment, configure the method for obtaining the 
address. The configuration of an IP address, a subnet mask, and a gateway address is not 
required.

For information on how to set an IP address, refer to "Protocol Settings" (P.181).

4

If the operating system on the client is Mac OS X 10.5 or later, enable the Bonjour port, and 
the Discovery feature that automatically detects printers on the IP network can be 
enabled.

Note

•

To print from a printer detected by Bonjour, the LPD port must be enabled in advance.

1) Select [Connectivity & Network Setup].

2) Select [Port Settings].

3) Select [Bonjour], and then select [Change Settings].

4) Select [Port Status], and then select [Change Settings].

5) Select [Enabled], and then select [Save].

5

Select [Close] repeatedly until the [Tools] screen is displayed.

6

Select [Close].

Note

•

Rebooting the machine may be required depending on the settings. When a message displayed on 
the screen, follow the message and reboot the machine.

7

Print a configuration report to confirm that the LPD port is enabled and that TCP/IP is set 
up correctly.

For information on how to print a configuration report, refer to "Print Reports" (P.90).

8

Configure other LPD or Port9100 settings as necessary. 

For information on how to set up the LPD port or Port9100, refer to "CentreWare Internet Services Setting Items" (P.312).

Step 3 Configuration on the Computer

To print from the machine, you need to install a print driver on your computer.

For information on the supported operating systems, refer to "Supported Operating Systems" (P.305). 

For information on the driver installation procedures, refer to the manual contained in the Media (Software/Product 
Manual).

You can print via TCP/IP (LPD) from a Macintosh computer for Mac OS X 10.5/10.6, Mac OS X 10.7 Lion, OS X 10.8 Mountain 
Lion, and OS X 10.9 Mavericks. For information on the installation procedures of the print driver for Mac OS X, refer to the 
manual contained in the Media (Software/Product Manual).

For information on the installation procedures of Adobe PostScript 3 Kit (optional), refer to the manual contained in the CD-
ROM provided with the Adobe PostScript 3 Kit (optional).

CentreWare Internet Services Setting Items

You can configure the following setting items using CentreWare Internet Services:

For details on the setting items, click [Help] at the upper right corner of the CentreWare Internet Services screen to see help.

Important •

To display the online help for CentreWare Internet Services, users need to have the environment to 
connect to the Internet. The communication fee shall be borne by you.

For information on how to start CentreWare Internet Services, refer to "Starting CentreWare Internet Services" (P.298).

z

Spool Destination for Jobs
([Properties] > [General Setup] > [Memory Settings] > [LPD])

Note

•

The spool destination can be configured when the LPD port is enabled.

Summary of Contents for ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ApeosPort-V 4070

Xerox B210 Manual preview
B210
Brand: Xerox Pages: 73
Xerox B210 Installation Manual preview
B210
Brand: Xerox Pages: 2
DataCard C3000 Datasheet preview
C3000
Brand: DataCard Pages: 2
IBM 3160 Introduction And Planning Manual preview
3160
Brand: IBM Pages: 102
Pandigital M1 Setup Instruction preview
M1
Brand: Pandigital Pages: 2
Xerox Phaser 6300/DN Repacking Manual preview
Phaser 6300/DN
Brand: Xerox Pages: 3
Xerox DocuColor 252 Specifications preview
DocuColor 252
Brand: Xerox Pages: 8
Xerox Versant 3100 Press Security Manual preview
Versant 3100 Press
Brand: Xerox Pages: 45
Oki OKIFAX 5050 Handbook preview
OKIFAX 5050
Brand: Oki Pages: 98
Konica Minolta Bizhub 4020 Shortcut Manual preview
Bizhub 4020
Brand: Konica Minolta Pages: 40
Xerox VersaLink C625 Manual preview
VersaLink C625
Brand: Xerox Pages: 14
Pantum M6500 series Faq preview
M6500 series
Brand: Pantum Pages: 126
Ricoh Aficio 1018 Operating Instructions Manual preview
Aficio 1018
Brand: Ricoh Pages: 74
Xerox N2125N - DocuPrint B/W Laser Printer Service Manual preview
N2125N - DocuPrint B/W Laser Printer
Brand: Xerox Pages: 335
Kyocera Mita 1900N - B/W Laser Printer Operation Manual preview
1900N - B/W Laser Printer
Brand: Kyocera Mita Pages: 286
Kodak ESP Office 6100 Series Extended User Manual preview
ESP Office 6100 Series
Brand: Kodak Pages: 94
Olivetti Copia 9915F Operation Manual preview
Copia 9915F
Brand: Olivetti Pages: 228
Unytouch UPI3FL-80mm User Manual preview
UPI3FL-80mm
Brand: Unytouch Pages: 12

Brands by name

Popular brands

Load more brands