manualshive.com logo in svg

Fuji Xerox ApeosPort-V 4070, Administrator'S Manual

The Fuji Xerox ApeosPort-V 4070 is a versatile multifunction printer designed for office use. To optimize its features, the Administrator's Manual is a comprehensive guide that can be downloaded for free from our website, providing step-by-step instructions and configuration options to enhance productivity and efficiency.

Share
Download
background image

Loading Paper

49

Pa
p

e

r a
nd O

ther

 Med

ia

2

Loading Paper

This section describes how to load paper.

„

Types of paper loaded in trays

The machine automatically detects the size and orientation of loaded paper in a tray, but 
not a paper type. Normally, each tray is set to plain paper. When loading paper other than 
plain paper, you must change the paper type setting. You can name paper types and can set 
up to five paper types as user-defined paper.

For information on changing the paper type settings, refer to "Changing the Paper Settings" (P.59).

„

Automatic Tray Selection

If you set paper source on the [Paper/Output] tab to [Paper Tray] in the PCL print driver's 
screen when printing, the machine automatically selects the paper tray according to the size 
and orientation of the document to be printed. This is called the Automatic Tray Selection.

When copying, selecting [Auto Select] for [Paper Supply] enables automatic tray selection. 
If the machine detects two or more corresponding trays for the automatic tray selection, the 
machine selects the tray with the highest priority specified in [Paper Type Priority] among 
the trays set under [Paper Type Settings]. Trays whose [Paper Type Priority] setting is set to 
[Auto Paper Off] are ignored in automatic tray selection. Also, if the [Paper Type Priority] 
settings are identical, the tray priority is determined by [Paper Tray Priority].

Note

•

Tray 5 cannot be selected in automatic tray selection.

•

When the paper runs out during copying or printing, select a tray containing the same sized paper 
and orientation, and the machine continues copying or printing (Auto Tray Switching feature). The 
machine cannot switch to a tray containing a paper type for which [Paper Type Priority] is set to 
[Auto Paper Off].

For information about [Paper Type], [Paper Type Priority], and [Paper Tray Priority] settings, and the paper substitute 
feature, refer to "Paper Tray Settings" (P.138). You can also set these settings from CentreWare Internet Services.

„

Adding paper

When the machine runs out of paper during copying or printing, a message appears on the 
touch screen. Add paper according to the message instructions. Copying or printing 
automatically resumes when paper is added.

Important •

Do not add paper while the machine is in the Power Saver mode. Add paper after exiting the Power 
Saver mode by pressing the <Power Saver> button, and then press the <Machine Status> button.

Note

•

Carefully fan the paper before loading it in a tray. Otherwise, the paper may stick together, resulting 
in paper jams, or multiple sheets being fed to the machine simultaneously.

Loading Paper in Trays 1 to 4 (Trays 3 and 4 (Two Tray Module) (Optional))

The following describes the procedure for loading paper in Trays 1 to 4.

When the machine runs out of paper during copying or printing, a message is displayed on 
the touch screen. Add paper according to the displayed instructions. Copying or printing 
automatically resumes when paper is added.

Note

•

Fan the paper well before loading paper in a tray. It prevents paper from sticking to each other and 
reduces paper jams.

For information on changing the paper size and orientation, refer to "Changing the Paper Size for Trays 1 to 4 (Trays 3 and 
4 (Two Tray Module) (Optional))" (P.54).

Summary of Contents for ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ApeosPort-V 4070

QMS Magicolor 6100 Supplementary Manual preview
Magicolor 6100
Brand: QMS Pages: 2
QMS 2060 WX User Manual preview
2060 WX
Brand: QMS Pages: 208
Samsung CLX-6260ND User Manual preview
CLX-6260ND
Brand: Samsung Pages: 368
Konica Minolta bizhub C250i Quick Manual preview
bizhub C250i
Brand: Konica Minolta Pages: 61
Oki C9650 Series User Manual preview
C9650 Series
Brand: Oki Pages: 126
Xerox WorkCentre Pro 32 Specification preview
WorkCentre Pro 32
Brand: Xerox Pages: 14
Wang System 2200 2231w-3 User Manual preview
System 2200 2231w-3
Brand: Wang Pages: 52
Oki C9000 Series User Manual preview
C9000 Series
Brand: Oki Pages: 204
Ricoh IM C6000 Series Quick Reference Copy Manual preview
IM C6000 Series
Brand: Ricoh Pages: 2
A&D AD-8118B Instruction Manual preview
AD-8118B
Brand: A&D Pages: 102
Ricoh Aficio AP3800C Setup Manual preview
Aficio AP3800C
Brand: Ricoh Pages: 84
Epson C11CE90201 Quick Manual preview
C11CE90201
Brand: Epson Pages: 17
Epson C11CB88201 Quick Manual preview
C11CB88201
Brand: Epson Pages: 44
Epson C11CA80201 Quick Manual preview
C11CA80201
Brand: Epson Pages: 56
Epson C11CA69201 Quick Manual preview
C11CA69201
Brand: Epson Pages: 64
Epson C11CA96201 Manual Rapide preview
C11CA96201
Brand: Epson Pages: 88
Epson C11CA79201 Quick Manual preview
C11CA79201
Brand: Epson Pages: 56
Epson C11CH42401 User Manual preview
C11CH42401
Brand: Epson Pages: 161

Brands by name

Popular brands

Load more brands